Effect Block
MOTIF XF Reference Manual
29
Basic Str
uct
ur
e
Basic Oper
ation
Connections
Basic Section
*1 The Bottom parameter is available only when the value is less than that of the Top
parameter.
*2 The Color parameter may not be effective depending on the values of the Mode and
Stage parameters.
*3 The Top parameter is available only when the value is more than that of the Bottom
parameter.
Mod Feedback
Determines the feedback level to the modulation.
Mod Gain
Determines the gain of the modulation.
Mod LPF Cutoff
Frequency
Determines the cutoff frequency of the low pass filter applied to
the modulated sound.
Mod LPF
Resonance
Determines the resonance of the low pass filter for the modulated
sound.
Mod Mix Balance
When “Noisy” is selected, this parameter determines the mix
balance of the modulated element.
When “Tech Modulation” is selected, this parameter determines
the volume of the modulated sound.
Mod Speed
Determines the modulation speed.
Mod Wave Type
Selects the wave type for modulation.
Mode
Determines the phaser type, or more specifically, the factor for
forming the phaser effect.
Modulation Phase
Determines the L/R phase difference of the modulated wave.
Move Speed
Determines how long it takes to move the sound from the current
status to the sound specified via the Vowel parameter.
Noise Input Level
Determines the noise level which is to be input.
Noise Level
Determines the noise level.
Noise LPF Cutoff
Frequency
Determines the cutoff frequency of the low pass filter applied to
the noise.
Noise LPF Q
Determines the resonance of the low pass filter applied to the
noise.
Noise Mod Depth
Determines the depth of the noise modulation.
Noise Mod Speed
Determines the speed of the noise modulation.
Noise Tone
Determines the characteristics of the noise.
On/Off Switch
Turns the isolator on or off.
OSC Frequency
Coarse
Determines the frequency at which the sine wave modulates the
amplitude of the input wave.
OSC Frequency
Fine
Determines the frequency finely at which the sine wave
modulates the amplitude of the input wave.
Output
Determines the level of the signal output from the effect block.
Output Gain
Determines the gain of the signal output from the effect block.
Output Level
Determines the level of the signal output from the effect block.
Output Level 1, 2
Determines the level of the signal output from the 1st block and
2nd block respectively.
Over Drive
Determines the degree and character of the distortion effect.
Pan 1, 2
Determines the pan for each of the 1st series and 2nd series.
Pan AEG Min
Level
This parameter of the Slice effect determines the minimum level
of the AEG applied to the panned sound.
Pan AEG Type
This parameter of the Slice effect determines the type of the AEG
applied to the panned sound.
Pan Depth
Determines the depth of the pan effect.
Pan Direction
Determines the direction toward which the stereo pan position of
the sound moves.
Pan Type
Determines the pan type.
Pedal Control
When “VCM Pedal Wah” is selected, this parameter determines
the cutoff frequency of the wah filter. For best results, assign the
this parameter to the Foot Controller in the Controller Set display,
then use the Foot Controller to control this parameter.
Pedal Response
Determines how the sound responds to the change of the
damper control.
Phase Shift Offset
Determines the offset value of the phase modulation.
Pitch 1, 2
Determines the pitch in semitones for each of the 1st series and
2nd series.
PM Depth
Determines the depth of the pitch modulation.
Pre Mod HPF
Cutoff Frequency
Determines the Cutoff frequency of the High Pass Filter before
the modulation.
Pre-LPF Cutoff
Frequency
Determines the Cutoff frequency of the Low Pass Filter before the
modulation.
Pre-LPF
Resonance
Determines the Resonance of the Low Pass Filter for the input
sound.
Presence
This parameter of the guitar amp effect controls high frequencies.
Ratio
Determines the ratio of the compressor.
Release
Determines the amount of time that elapses between the
releasing of a key and the end of the compressor effect.
Release Curve
Determines the release curve of the envelope follower.
Release Time
Determines the release time of the envelope follower.
Resonance
Determines the resonance of the filter.
Resonance Offset
Determines the resonance as offset.
Reverb Delay
Determines the delay time from the early reflections until the
reverberations.
Reverb Time
Determines the reverb time.
Room Size
Determines the size of the room in which the instrument sounds.
Rotor Speed Fast
Determines the speed of the rotor when the slow/fast switch is set
to “fast.”
Rotor Speed Slow
Determines the speed of the rotor when the slow/fast switch is set
to “slow.”
Rotor/Horn
Balance
Determines the volume balance of the horn and rotor.
Sampling Freq.
Control
Controls the sampling frequency.
Parameter name
Descriptions
Sensitivity
When one of “Dynamic Flanger,” “Dynamic Phaser,” and the TEC
effects is selected, this parameter determines the sensitivity of
the modulation applied to the input change.
When one of the VCM Touch Wah effects is selected, this
parameter determines the sensitivity of the wah filter’s change
applied to the input change.
Slow-Fast Time of
Horn
Determines how long it takes for the rotation speed of the horn to
change from the current speed (slow or fast) to the other one
(fast or slow) when the rotation speed is switched.
Slow-Fast Time of
Rotor
Determines how long it takes for the rotation speed of the rotor to
change from the current speed (slow or fast) to the other one
(fast or slow) when the rotation speed is switched.
Space Type
Selects the type of space simulation.
Speaker Type
Selects the type of speaker simulation.
Speed
When “VCM Flanger” is selected, this parameter determines the
frequency of the LFO wave which controls the cyclic change of
the delay modulation.
When any of the phaser types is selected, this parameter
determines the frequency of the LFO wave which controls the
cyclic change of the phase modulation.
When “VCM Auto Wah” is selected, this parameter determines
the speed of the LFO.
Speed Control
Switches the rotary speed.
Spread
Determines the spread of the sound.
Stage
Determines the step number of the phase shifter.
Threshold
Determines the minimum input level at which the effect is
applied.
Top
*3
Determines the maximum value of the wah filter.
Type
When “VCM Flanger” is selected, this parameter determines the
flanger type.
When any of the wah effects is selected, this parameter
determines the type of the Auto Wah.
When “Early Reflection” is selected, this parameter determines
the type of the reflection sound.
Vocoder Attack
Determines the attack time of the Vocoder sound.
Vocoder Release
Determines the release time of the Vocoder sound.
Vowel
Selects a vowel type.
Wall Vary
Determines the wall status of the simulated room. Higher settings
produces more diffuse reflections.
Width
Determines the width of the simulated room.
Word Length
Determines the degree of sound roughness.
Parameter name
Descriptions