Yamaha HTR-5230 Скачать руководство пользователя | Manualshive

Страница: 22 / 61

background image

18

4

Adjust BALANCE on the
front panel so that the
sound output level of the
right main speaker and the
left main speaker is the
same.

5

Press TIME/LEVEL
repeatedly to select the
speaker to be adjusted.

“CENTER”, “R SUR.” or
“L SUR.” appears on the
display.

6

Press + to raise and – to
lower the level. Adjust the
sound output levels of the
center speaker and the
rear speakers so that they
become almost the same
as that of the main
speakers.

While adjusting, the test tone is
heard from the selected speaker.

Note

• You cannot adjust the delay time while the test tone is being heard

even if “DELAY” appears on the display.

7

When the adjustment is complete, press TEST.

“TEST OFF” appears on the display and the test tone
stops.

Note

• If “CENTER SP” in the SET MENU is set to the NONE position,

the sound output level of the center speaker cannot be adjusted in
step 6. The center channel sound is automatically output from the
right and left main speakers.

y

• Once you have completed the adjustments, you can only adjust

the overall volume level of your audio system by using VOLUME
(or VOLUME (

u

/

d

)).

• If there is insufficient sound output from the center and rear

speakers, you may decrease the main speaker output level by
setting “MAIN LVL” in the SET MENU to “–10 dB”. (Refer to
page 33 for details.)

ADJUSTING THE SPEAKER BALANCE

Front panel

L

R

0103V39608-18_EN(UCA)

1/11/0, 5:29 PM

18

«
...
20
21
22
23
24
...
»

Содержание HTR-5230






























































Отзывы:

Нет отзывов

Похожие инструкции для HTR-5230

Бренд: Magnasonic Страницы: 2

Бренд: Magnat Audio Страницы: 64

IMPERIAL HD 2 basic

Бренд: DigitalBox Страницы: 96

Бренд: ADTRAN Страницы: 24

Бренд: ZoneVu Страницы: 33

SD 236BT/RDS/USB/AX

Бренд: Majestic Страницы: 6

Бренд: Immersion Страницы: 5

Бренд: Denon Страницы: 56

Бренд: WCCDYZDTG Страницы: 5

Бренд: Onkyo Страницы: 285

Бренд: Columbus Страницы: 3

CAT-5 Receiver Card PE1004CF

Бренд: Altinex Страницы: 13

Бренд: AX Страницы: 16

Бренд: Hallicrafters Страницы: 16

Бренд: Daytona Страницы: 143

Бренд: Carver Страницы: 37

Бренд: Haier Страницы: 25

Бренд: Haier Страницы: 29

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды