Yamaha HTR-5230 Скачать руководство пользователя | Manualshive

Страница: 14 / 61

background image

10

Connecting the Antennas

Both AM and FM indoor antennas are included with this unit. In general, these antennas should provide sufficient signal
strength. However, a properly installed outdoor antenna provides clearer reception than an indoor one. If you experience poor
reception quality, an outdoor antenna may improve the quality.

Connect each antenna correctly to the designated terminals.

■

Indoor FM antenna (included)

Firmly insert the connector into the FM ANT terminal. The
indoor FM antenna is only a simple antenna. For reception
with better sound quality, installing the outdoor FM antenna
(commercially available) is recommended.

Note

• Do not connect an outdoor FM antenna and the indoor FM

antenna at the same time.

■

Outdoor FM antenna

You may be unable to obtain good FM radio reception
depending on your local conditions (distance from the
broadcasting station, interposing buildings and
mountains, etc.). Consult your dealer or authorized service
center and be sure to install an antenna that suits your local
conditions.
Install the outdoor FM antenna (commercially available) in
a high place as far away from any roads as possible to avoid
being affected by automobile ignition noise.

CONNECTIONS

Antenna adapter
(included for U.S.A. and
Canada models)

Note

Use this adapter to match
with F-type connector

75-ohm coaxial cable

75-ohm/300-ohm antenna
adapter

300-ohm feeder

Indoor FM
antenna

0103V39608-18_EN(UCA)

1/11/0, 5:28 PM

10

«
...
12
13
14
15
16
...
»

Содержание HTR-5230






























































Отзывы:

Нет отзывов

Похожие инструкции для HTR-5230

Бренд: Sylvania Страницы: 8

Бренд: ESX Страницы: 16

Бренд: Lectrosonics Страницы: 12

Бренд: Yaesu Страницы: 34

NEO-FiberLink-2

Бренд: G&D Страницы: 32

Бренд: Aria Страницы: 12

Бренд: RF Central Страницы: 41

TWOMOBILE MK II

Бренд: GAREX Страницы: 18

Бренд: TTI Страницы: 39

Бренд: Icom Страницы: 32

Бренд: Beltek Страницы: 16

Бренд: Intel Страницы: 80

Бренд: Laird Страницы: 8

Бренд: Vizualogic Страницы: 44

Бренд: SecurityMan Страницы: 17

Бренд: Ferguson Страницы: 42

Бренд: Onkyo Страницы: 110

Бренд: Nextar Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды