Yamaha HTR-5230 страница 51 Скачать руководство пользователя

Страница: 51 / 61

English

ASIC OPERA

TION

AD
V

ANCED OPERA

TION

APPENDIX

INTR

ODUCTION

PREP

ARA

TION

■

Remote control

This unit is in the standby mode.

Turn on the power of the unit.

SYMPTOM

CAUSE

REMEDY

Refer to
page

The remote control does
not work.

Direct sunlight or lighting (from an inverter
type of fluorescent lamp, etc.) is striking the
remote control sensor of this unit.

Reposition the unit.

The batteries are weak.

Replace all batteries with new ones.

The unit or other
component cannot be
controlled.

The component to be controlled has not been
selected.

Press one of the component selector buttons
which corresponds to the component to be
controlled.

The manufacturer’s code has not been set
properly.

Enter the code again.

Try setting another code for the same
manufacturer.

■

Others

SYMPTOM

CAUSE

REMEDY

Refer to
page

The sound is degraded
when listening with
headphones to a tape
deck or CD player
connected to this unit.

There is noise
interference from digital
or high-frequency
equipment, or the unit.

The unit is too close to the digital or high-
frequency equipment.

Move the unit further away from such
equipment.

TROUBLESHOOTING

—

0110V39645-50_EN(UCA)

1/12/0, 9:43 AM

Содержание HTR-5230






























































Результаты поиска

Содержание HTR-5230

Отзывы:

Похожие инструкции для HTR-5230

Бренды по названию

Популярные бренды

Yamaha HTR-5230, Руководство пользователя

Результаты поиска

Содержание HTR-5230

Отзывы:

Похожие инструкции для HTR-5230

Бренды по названию

Популярные бренды