Yamaha FZ8NB Скачать руководство пользователя

Страница: 44 / 108

OPERATION AND IMPORTANT RIDING POINTS

6-4

1600 km (1000 mi) and beyond

The vehicle can now be operated nor-
mally.

NOTICE

ECA10310

●

Keep the engine speed out of
the tachometer red zone.

●

If any engine trouble should oc-
cur during the engine break-in
period, immediately have a
Yamaha dealer check the vehi-
cle.

EAU17213

Parking

When parking, stop the engine, and
then remove the key from the main
switch.

WARNING

EWA10311

●

Since the engine and exhaust
system can become very hot,
park in a place where pedestri-
ans or children are not likely to
touch them and be burned.

●

Do not park on a slope or on soft
ground, otherwise the vehicle
may overturn, increasing the
risk of a fuel leak and fire.

●

Do not park near grass or other
flammable materials which
might catch fire.

U39P11E0.book Page 4 Monday, August 1, 2011 5:00 PM

Содержание FZ8NB













































































































Результаты поиска

Содержание FZ8NB

Отзывы:

Похожие инструкции для FZ8NB

Бренды по названию

Популярные бренды

Yamaha FZ8NB, Руководство пользователя

Результаты поиска

Содержание FZ8NB

Отзывы:

Похожие инструкции для FZ8NB

Бренды по названию

Популярные бренды