Yamaha FZ8NB Скачать руководство пользователя | Manualshive

Страница: 58 / 108

background image

PERIODIC MAINTENANCE AND ADJUSTMENT

7-14

7

3. If the coolant is at or below the

minimum level mark, remove pan-
el A to access the coolant reser-
voir. (See page 7-9.)

4. Remove the coolant reservoir cap,

add coolant to the maximum level
mark, and then install the reservoir
cap.

WARNING! Remove only

the coolant reservoir cap. Never
attempt to remove the radiator
cap when the engine is hot.

[EWA15161]

NOTICE:

If coolant is not

available, use distilled water or
soft tap water instead. Do not
use hard water or salt water
since it is harmful to the engine.

If water has been used instead
of coolant, replace it with cool-
ant as soon as possible, other-
wise the cooling system will not
be protected against frost and
corrosion. If water has been
added to the coolant, have a
Yamaha dealer check the anti-
freeze content of the coolant as
soon as possible, otherwise the
effectiveness of the coolant will
be reduced.

[ECA10472]

5. Install the panel.

EAU33031

Changing the coolant

The coolant must be changed at the in-
tervals specified in the periodic mainte-
nance and lubrication chart. Have a
Yamaha dealer change the coolant.

WARNING! Never attempt to remove
the radiator cap when the engine is
hot.

[EWA10381]

1. Coolant reservoir
2. Maximum level mark

3. Minimum level mark

1
2
3

1. Coolant reservoir cap

Coolant reservoir capacity (up to
the maximum level mark):

0.25 L (0.26 US qt, 0.22 Imp.qt)

1

U39P11E0.book Page 14 Monday, August 1, 2011 5:00 PM

«
...
56
57
58
59
60
...
»

Содержание FZ8NB













































































































Отзывы:

Нет отзывов

Похожие инструкции для FZ8NB

Бренд: GAS GAS Страницы: 142

Advanced Million Color Mini Motorcycle Lighting Kit

Бренд: LedGlow Страницы: 3

Бренд: Honda Страницы: 190

2007 enducross EC

Бренд: GAS GAS Страницы: 72

Бренд: Corbin Страницы: 4

Бренд: hepco & becker Страницы: 7

Бренд: SHERCO Страницы: 102

690 Enduro AUS 2010

Бренд: KTM Страницы: 265

Бренд: Fantic Motor Страницы: 60

Бренд: Caberg Страницы: 16

Бренд: hepco & becker Страницы: 2

Бренд: hepco & becker Страницы: 3

Бренд: digades Страницы: 10

Бренд: Shark Страницы: 8

Бренд: Shark Страницы: 24

Бренд: Beta Страницы: 38

Бренд: Beta Страницы: 79

Pegaso 650 2005

Бренд: APRILIA Страницы: 139

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды