Yamaha FZ8NB Скачать руководство пользователя

Страница: 70 / 108

PERIODIC MAINTENANCE AND ADJUSTMENT

7-26

TIP

Using the alignment marks on each
side of the swingarm, make sure that
both drive chain pullers are in the same
position for proper wheel alignment.

3. Tighten the axle nut, then the lock-

nuts to their specified torques.

4. Make sure that the drive chain pull-

ers are in the same position, the
drive chain slack is correct, and
the drive chain moves smoothly.

EAU23025

Cleaning and lubricating the
drive chain

The drive chain must be cleaned and
lubricated at the intervals specified in
the periodic maintenance and lubrica-
tion chart, otherwise it will quickly wear
out, especially when riding in dusty or
wet areas. Service the drive chain as
follows.

NOTICE

ECA10583

The drive chain must be lubricated
after washing the motorcycle, riding
in the rain or riding in wet areas.

1. Clean the drive chain with kero-

sene and a small soft brush.

NOTICE:

To prevent damaging

the O-rings, do not clean the
drive chain with steam cleaners,
high-pressure washers or inap-
propriate solvents.

[ECA11121]

2. Wipe the drive chain dry.
3. Thoroughly lubricate the drive

chain with a special O-ring chain
lubricant.

NOTICE:

Do not use

engine oil or any other lubri-
cants for the drive chain, as they

1. Drive chain slack adjusting bolt

1. Alignment marks

2. Drive chain puller

(a)

(b)

Tightening torques:

Axle nut:

150 Nm (15 m·kgf, 108 ft·lbf)

Locknut:

16 Nm (1.6 m·kgf, 12 ft·lbf)

U39P11E0.book Page 26 Monday, August 1, 2011 5:00 PM

Содержание FZ8NB













































































































Результаты поиска

Содержание FZ8NB

Отзывы:

Похожие инструкции для FZ8NB

Бренды по названию

Популярные бренды

Yamaha FZ8NB, Руководство пользователя

Результаты поиска

Содержание FZ8NB

Отзывы:

Похожие инструкции для FZ8NB

Бренды по названию

Популярные бренды