Yamaha F9.9 Скачать руководство пользователя

Страница: 52 / 112

Operation

Remove the fuel tank from the boat.

To loosen the air vent screw, turn it coun-
terclockwise until it stops.

While pressing and holding the pressure
relief tab under the fuel tank cap, slowly
turn the fuel tank cap counterclockwise
1/4 turn.

TIP:

Release the fuel vapor contained in the fuel
tank.
6.

While pressing and holding the pressure
relief tab under the fuel tank cap again,
turn the fuel tank cap counterclockwise
to remove it.

Fill the fuel tank with fuel.

WARNING! Do

not overfill. Otherwise fuel can expand
and overflow if the temperature in-
creases.

[EWM02611]

TIP:



Wipe up any spilled gasoline immediately
with dry rags.

1. Air vent screw

1. Pressure relief tab
2. Fuel tank cap

ZMU07444

ZMU07445

ZMU07446

1. Pressure relief tab
2. Fuel tank cap

Fuel tank capacity:

12 L (3.17 US gal, 2.64 Imp.gal)

ZMU07447

U6DR38E0.book Page 46 Tuesday, November 27, 2018 2:08 PM

Yamaha

Motor

Corporation

Содержание F9.9

















































































































Результаты поиска

Содержание F9.9

Отзывы:

Похожие инструкции для F9.9

Бренды по названию

Популярные бренды

Yamaha F9.9, Руководство пользователя

Результаты поиска

Содержание F9.9

Отзывы:

Похожие инструкции для F9.9

Бренды по названию

Популярные бренды