Yamaha F9.9 Скачать руководство пользователя | Manualshive

Страница: 49 / 112

background image

Operation

43

EMU27168

Engine oil

1.

Put the outboard motor in an upright po-
sition (not tilted).

NOTICE:

If the motor

is not level, the oil level indicated on
the dipstick may not be accurate.

[ECM01791]

2.

Remove oil dipstick and wipe it clean.

3.

Insert the dipstick and remove it again.
Be sure to completely insert the dipstick
into the dipstick guide, otherwise the oil
level measurement will be incorrect.

4.

Check the oil level using the dipstick to
be sure the level falls between the upper
and lower marks. Fill with oil if it is below
the lower mark, or drain to the specified
level if it is above the upper mark.

EMU40412

Outboard motor



Check that the outboard motor is mounted
properly and check the outboard motor
mounting bolts for looseness.



Check the propeller for damage.



Check for engine oil leaks.

EMU36494

Flushing device

Check that the flushing device’s garden hose
connector is securely screwed on to the fit-
ting on the bottom cowling.

NOTICE:

If the

garden hose connector is not properly
connected, cooling water can leak out and
the engine can overheat during operation.

[ECM01802]

1. Clip
2. Engine shut-off cord (lanyard)

1. Oil dipstick

ZMU06

8

73

1

2

1

ZMU07825

1. Oil dipstick
2. Upper mark
3. Lower mark

1. Fitting
2. Garden hose connector
3. Flushing device

3 2

1

ZMU07792

1

2

3

ZMU06070

U6DR38E0.book Page 43 Tuesday, November 27, 2018 2:08 PM

©2020

Yamaha

Motor

Corporation

«
...
47
48
49
50
51
...
»

Содержание F9.9

















































































































Отзывы:

Нет отзывов

Похожие инструкции для F9.9

Бренд: Xilinx Страницы: 40

Бренд: JETWAY Страницы: 58

NuMicro NuTiny-SDK-NANO100

Бренд: Nuvoton Страницы: 18

DQ963FX - Desktop Board Motherboard

Бренд: Intel Страницы: 72

PRESTIGE X570 CREATION

Бренд: MSI Страницы: 88

Бренд: DFI Страницы: 92

Бренд: Mercury Страницы: 57

Бренд: Maxus Страницы: 59

MAG B560M BAZOOKA

Бренд: MSI Страницы: 136

Бренд: MSI Страницы: 134

XtremeDSP Spartan-3A DSP 3400A...

Бренд: Xilinx Страницы: 50

Бренд: Exar Страницы: 9

Бренд: DFI Страницы: 110

Бренд: DFI Страницы: 124

Бренд: MiTAC Страницы: 84

Бренд: Lattice Страницы: 12

Бренд: Ublox Страницы: 23

Бренд: VIA Technologies Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды