Yamaha F9.9 Скачать руководство пользователя

Страница: 19 / 112

General information

EMU33913

Contents of labels

The above warning labels mean as follows.

WARNING

EWM01692

Emergency starting does not have start-
in-gear protection. Ensure shift control is
in neutral before starting engine.

WARNING

EWM01682



Keep hands, hair, and clothing away
from rotating parts while the engine is
running.



Do not touch or remove electrical parts
when starting or during operation.

WARNING

EWM01672



Read Owner’s Manuals and labels.



Wear an approved personal flotation de-
vice (PFD).



Attach engine shut-off cord (lanyard) to
your PFD, arm, or leg so the engine
stops if you accidentally leave the helm,
which could prevent a runaway boat.

6EE-G2794-40

6EE-H1994-40

6EE-H1995-40

6EE-G2794-50

6EE-H1994-50

6EE-H1995-50

ZMU05740

U6DR38E0.book Page 13 Tuesday, November 27, 2018 2:08 PM

Yamaha

Motor

Corporation

Содержание F9.9

















































































































Результаты поиска

Содержание F9.9

Отзывы:

Похожие инструкции для F9.9

Бренды по названию

Популярные бренды

Yamaha F9.9, Руководство пользователя

Результаты поиска

Содержание F9.9

Отзывы:

Похожие инструкции для F9.9

Бренды по названию

Популярные бренды