Yamaha F9.9 Скачать руководство пользователя | Manualshive

Страница: 44 / 112

background image

Installation

38

EMU26903

Installation

The information presented in this section is
intended as reference only. It is not possible
to provide complete instructions for every
possible boat and motor combination. Proper
mounting depends in part on experience and
the specific boat and motor combination.

WARNING

EWM01591



Overpowering a boat could cause se-
vere instability. Do not install an out-
board motor with more horsepower
than the maximum rating on the capaci-
ty plate of the boat. If the boat does not
have a capacity plate, consult the boat
manufacturer.



Improper mounting of the outboard mo-
tor could result in hazardous conditions
such as poor handling, loss of control,
or fire hazards. For permanently mount-
ed models, your dealer or other person
experienced in proper rigging should
mount the motor.

EMU34802

Mounting the outboard motor

NOTICE

ECM01681

Do not hold the top cowling when mount-
ing or dismounting the outboard motor.
The top cowling could come off, causing
the outboard motor to fall.

1.

Be sure to mount the outboard motor
while the boat is on land. If the boat is on
the water, move it to an area on land.

2.

To prevent steering movement, turn the
adjuster lever to “A” (if equipped with the
adjuster lever). To hold the steering
bracket easily, raise the tiller handle to
the vertical position (if equipped with the
tiller handle).

3.

Hold the handgrip and steering bracket
as shown in the illustration and lift up the
outboard motor using two people.

1. Steering bracket
2. Handgrip

1

2

ZMU07878

U6DR38E0.book Page 38 Tuesday, November 27, 2018 2:08 PM

©2020

Yamaha

Motor

Corporation

«
...
42
43
44
45
46
...
»

Содержание F9.9

















































































































Отзывы:

Нет отзывов

Похожие инструкции для F9.9

Бренд: Analog Devices Страницы: 8

Бренд: Intertec Components Страницы: 3

Бренд: Aaeon Страницы: 30

Бренд: DFI Страницы: 99

Бренд: Texas Instruments Страницы: 101

Бренд: ASROCK Страницы: 6

Бренд: Ublox Страницы: 38

790XT-G35 series

Бренд: MSI Страницы: 103

Бренд: Aaeon Страницы: 108

GA-B150M-D3V DDR3

Бренд: Gigabyte Страницы: 4

Бренд: Watersnake Страницы: 20

Бренд: Gigabyte Страницы: 34

OPTIREG PMIC TLF30682QVS01

Бренд: Infineon Страницы: 24

Desktop Board D845GLVA

Бренд: Intel Страницы: 72

Бренд: ASROCK Страницы: 62

Бренд: ASROCK Страницы: 65

Бренд: VIA Technologies Страницы: 16

Бренд: VIA Technologies Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды