Yamaha F9.9 Скачать руководство пользователя | Manualshive

Страница: 50 / 112

background image

Operation

44

EMU36956

Install top cowling

1.

Be sure that the cowling lock lever is re-
leased.

2.

Be sure that the rubber seal is seated all
the way around the top cowling.

3.

Place the top cowling on the bottom
cowling.

4.

Check to be sure the rubber seal is seat-
ed correctly between the top cowling
and the bottom cowling.

5.

Move the cowling lock lever to lock the
top cowling as shown.

NOTICE:

If the

top cowling is not installed correctly,
water spray under the top cowling can
damage the engine, or the top cowling
can blow off at high speeds.

[ECM01992]

After installing, check the fitting of the top
cowling by pushing it with both hands. If the
top cowling is loose, have it repaired by your
Yamaha dealer.

EMU34783

Checking power tilt system

WARNING

EWM01971



Never get under the lower unit while it is
tilted, even when the tilt support knob is
locked. Severe injury could occur if the
outboard motor accidentally falls.



Body parts can be crushed between the
motor and the clamp bracket when the
motor is trimmed or tilted.



Be sure no one is near the outboard mo-
tor before performing this check.

1.

Check the power tilt unit for any sign of
oil leaks.

2.

Operate each of the power tilt switches
to check that all switches work.

3.

Tilt the outboard motor up and check
that the tilt rod is pushed out completely.

1. Top cowling
2. Rubber seal

1. Cowling lock lever

1

2

ZMU07827

1

ZMU07828

ZMU07829

U6DR38E0.book Page 44 Tuesday, November 27, 2018 2:08 PM

©2020

Yamaha

Motor

Corporation

«
...
48
49
50
51
52
...
»

Содержание F9.9

















































































































Отзывы:

Нет отзывов

Похожие инструкции для F9.9

Бренд: Yamaha Страницы: 232

Бренд: Advantech Страницы: 3

Бренд: Supermicro Страницы: 100

Бренд: Supermicro Страницы: 127

Бренд: Norco Страницы: 60

Бренд: Gigabyte Страницы: 88

Бренд: Shuttle Страницы: 50

Бренд: Advantech Страницы: 6

Бренд: Gigabyte Страницы: 96

Бренд: Yamaha Страницы: 98

Бренд: Yamaha Страницы: 105

Lanparty JR P45-T2RS

Бренд: DFI Страницы: 146

Бренд: DFI Страницы: 183

Бренд: Supero Страницы: 95

Бренд: Supero Страницы: 108

Бренд: Supero Страницы: 99

Supero X8DTU-6F+

Бренд: Supero Страницы: 111

Supero X7SBL-LN1/LN2

Бренд: Supero Страницы: 95

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды