Yamaha F50A Скачать руководство пользователя

Страница: 130 / 403

POWR

Power unit

5-3

62Y3A11

Symptom: Engine cracks, but will not start.

• Check the ignition system.
• Check the fuel system.
• Check the compression pressure of power unit.

Wet spark
plugs?

Does the
engine start?

Wet spark
plugs?

Out of specifi-
cation?

Check the condition of the spark
plugs.

Check the fuel system.

Failure in starting operation

Check the fuel system.

Check the condition of the spark
plugs again.

Check the compression pres-
sure of the combustion chamber.

Check the ignition system out-
put peak voltage.

Check the valve
clearance.

WARNING

• Do not touch any of

the connections of
the spark gap tester
leads.

• Do not let sparks

leak out of the
removed spark plug
caps.

• Keep flammable

gas or liquids away,
since this test can
produce sparks.

Start the engine using dried or
new spark plugs.

Adjust the valve
clearance.

Yes

Check the ignition spark using the spark gap tester.

Below the
spark gap
specification?

Yes

Check the cylinder head,
cylinger body, and piston
assembly.

Содержание F50A




















































































































































































































































































































































































































Результаты поиска

Содержание F50A

Отзывы:

Похожие инструкции для F50A

Бренды по названию

Популярные бренды

Yamaha F50A, Руководство по обслуживанию

Результаты поиска

Содержание F50A

Отзывы:

Похожие инструкции для F50A

Бренды по названию

Популярные бренды