Yamaha F50A Скачать руководство пользователя

Страница: 187 / 403

62Y3A11

5-60

1
2
3
4
5
6
7
8

Measure the crankshaft runout. Replace
the crankshaft if out of specification.

Checking the crankshaft main
journal oil clearance

Clean the bearings, main journals, and
bearing portions of the crankcase and
cylinder body.

Place the cylinder body upside down on
a bench.

Install half of the bearings

and the

crankshaft

into the cylinder body

CAUTION:

Install the bearings in their original posi-
tions.

NOTE:

Insert the projection

of the bearing into the

notch in the cylinder body.

Put a piece of Plastigauge

(PG-1) on

each main journal parallel to the crank-
shaft.

NOTE:

Do not put the Plastigauge (PG-1) over the
oil hole in the main journals of the crankshaft.

Install the remaining half of the bearings
into the crankcase.

NOTE:

Insert the projection of the bearing into the
notch in the crankcase.

Install the crankcase onto the cylinder
body and apply engine oil onto the
threads of the crankcase bolts.

Tighten the crankcase bolts to the speci-
fied torques in two stages and in the
sequence shown.

Crankshaft runout limit:

0.04 mm (0.0016 in)

Cylinder body

Содержание F50A




















































































































































































































































































































































































































Результаты поиска

Содержание F50A

Отзывы:

Похожие инструкции для F50A

Бренды по названию

Популярные бренды

Yamaha F50A, Руководство по обслуживанию

Результаты поиска

Содержание F50A

Отзывы:

Похожие инструкции для F50A

Бренды по названию

Популярные бренды