Yamaha F50A Скачать руководство пользователя

Страница: 86 / 403

CHK

ADJ

Periodic checks and adjustments

3-11

62Y3A11

Turn the flywheel clockwise and align the
“4” mark

on the driven sprocket with

the “

” mark

on the cylinder head.

CAUTION:

Do not turn the flywheel counterclock-
wise, otherwise the valve system may be
damaged.

Check the intake valve clearance for cyl-
inders #3 and #4, and the exhaust valve
clearance for cylinders #2 and #4. Adjust
if out of specification.

NOTE:

Adjust the valve clearance when the engine
is cold.

Loosen the locknut

, and then turn the

adjusting screw

until the specified

valve clearance is obtained.

NOTE:

• To decrease the valve clearance, turn the

adjusting screw clockwise.

• To increase the valve clearance, turn the

adjusting screw counterclockwise.

Tighten the locknut, and then check the
valve clearances. Adjust if necessary.

Install the cylinder head cover, fuel
pump, and spark plugs.

10. Connect the blowby hose and high-ten-

sion cords, and then install the flywheel
magnet cover.

Checking the spark plugs

Disconnect the high-tension cords, and
then remove the spark plugs.

Valve clearance:

Intake

0.20

0.05 mm (0.008

0.002 in)

Exhaust

0.30

0.05 mm (0.012

0.002 in)

Содержание F50A




















































































































































































































































































































































































































Результаты поиска

Содержание F50A

Отзывы:

Похожие инструкции для F50A

Бренды по названию

Популярные бренды

Yamaha F50A, Руководство по обслуживанию

Результаты поиска

Содержание F50A

Отзывы:

Похожие инструкции для F50A

Бренды по названию

Популярные бренды