manualshive.com logo in svg

Yamaha F50A, Руководство по обслуживанию

"Yamaha F50A" - высококачественный лодочный мотор с мощностью 50 л.с. Для всех владельцев это обязательно иметь "Owner's Manual". Вы можете скачать руководство бесплатно на manualshive.com. Получите подробную информацию об установке, обслуживании и эксплуатации вашего мотора, чтобы он работал на высшем уровне.

Поделиться
Скачать
background image

62Y3A11

i-2

1
2
3
4
5
6
7
8

Checking the piston diameter ...................5-56
Checking the piston pin.............................5-58
Checking the piston pin boss bore............5-58
Checking the piston ring grooves..............5-58
Checking the piston ring side clearance ...5-58
Checking the piston rings..........................5-57
Checking the power trim and 

tilt fluid level ............................................3-16

Checking the power trim and tilt motor .....7-75
Checking the power trim and 

tilt operation ............................................3-16

Checking the power trim and tilt relay.......7-79
Checking the power trim and 

tilt switch/trailer switch ............................7-80

Checking the Prime Start ..........................4-20
Checking the propeller ..............................3-19
Checking the propeller shaft ........... 6-15

, 

6-55

Checking the propeller shaft 

housing ......................................... 6-15

, 

6-54

Checking the pulser coil............................8-16
Checking the pulser coil air gap ................8-16
Checking the Rectifier Regulator ..............8-26
Checking the remote control cables..........1-34
Checking the rocker arms and 

rocker arm shaft ......................................5-45

Checking the shift rod and shift cam .........6-25
Checking the shift rod assembly 

operation .................................................7-29

Checking the spark plug caps...................8-14
Checking the spark plugs..........................3-11
Checking the starter motor operation........8-24
Checking the starter motor pinion .............8-23
Checking the starter relay .........................8-20
Checking the steering wheel/

tiller handle..............................................1-34

Checking the thermostat ...........................3-12
Checking the thermoswitch .......................8-18
Checking the throttle cable and 

shift cable................................................7-15

Checking the throttle cable and shift rod...7-23
Checking the throttle cable operation .......3-13
Checking the tilt cylinder and 

trim cylinder.............................................7-64

Checking the tilt system ............................1-35
Checking the timing belt..............................3-7
Checking the timing belt and sprockets ....5-32
Checking the top cowling ............................3-4
Checking the trim sensor ..........................7-80
Checking the valve clearance ...................3-10
Checking the valve guides ........................5-41
Checking the valve seat............................5-42
Checking the valve springs .......................5-40
Checking the valves..................................5-40

Checking the water pump ......................... 6-14
Checking the water pump and shift rod .... 6-47
Checking the wiring harness (10 pins) ..... 8-20
Clamp brackets......................................... 7-43
Control system.......................................... 3-13
Cooling water hose ..................................... 4-3
Cylinder body............................................ 5-51
Cylinder head ........................................... 5-35

D.

Dimensions............................................... 2-19
Disassembling the cylinder body .............. 5-55
Disassembling the drive shaft................... 6-61
Disassembling the drive shaft assembly .. 6-23
Disassembling the forward gear ......6-23

, 

6-61

Disassembling the fuel pump ..................... 4-9
Disassembling the gear pump .................. 7-64
Disassembling the lower case .........6-24

, 

6-62

Disassembling the oil pan......................... 7-39
Disassembling the propeller shaft 

assembly .......................................6-14

, 

6-54

Disassembling the propeller shaft 

housing ..........................................6-13

, 

6-53

Disassembling the tilt cylinder .................. 7-63
Disassembling the trim cylinder ................ 7-63
Disassembly and assembly ........................ 1-4
Drive shaft and lower case (F50/F50A) .... 6-21
Drive shaft and lower case 

(T50/FT50B, FT50C) .............................. 6-59

E.

Electrical ............................................2-9

, 

2-16

Electrical components ................................ 8-5

F.

Features and benefits................................. 1-6
Fire prevention............................................ 1-3
Front view ................................................... 8-6
Fuel and blowby hoses ............................... 4-2
Fuel filter and fuel pump ............................. 4-7
Fuel line ...................................................... 4-5
Fuel system ................................................ 3-4

G.

Gear pump................................................ 7-59
General..................................................... 3-19
General specifications ................................ 2-1
General torques........................................ 2-31
Good working practices .............................. 1-4

Содержание F50A




















































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для F50A

IEI Technology KINO-DQM871 User Manual preview
KINO-DQM871
Бренд: IEI Technology Страницы: 211
IEI Technology IOWA-MARK Quick Installation Manual preview
IOWA-MARK
Бренд: IEI Technology Страницы: 8
IEI Technology KINO-G45A Quick Installation Manual preview
KINO-G45A
Бренд: IEI Technology Страницы: 8
Waveshare NRF52840 User Manual preview
NRF52840
Бренд: Waveshare Страницы: 72
Portwell ROBO-8713SGA User Manual preview
ROBO-8713SGA
Бренд: Portwell Страницы: 86
Raptor C1P9S01 User Manual preview
C1P9S01
Бренд: Raptor Страницы: 59
OLIMEX A20-OLINUXINO-LIME User Manual preview
A20-OLINUXINO-LIME
Бренд: OLIMEX Страницы: 49
Analog Devices ADUX1020 User Manual preview
ADUX1020
Бренд: Analog Devices Страницы: 9
DFI E586-ICP User Manual preview
E586-ICP
Бренд: DFI Страницы: 96
Honda BF 30 DK2 SHGU Instructions For Use Manual preview
BF 30 DK2 SHGU
Бренд: Honda Страницы: 132
Advantech ASMB-820-00A1E User Manual preview
ASMB-820-00A1E
Бренд: Advantech Страницы: 88
Rosch Computer MS-98H4 Manual preview
MS-98H4
Бренд: Rosch Computer Страницы: 52
MSI MAG B560M BAZOOKA Manual preview
MAG B560M BAZOOKA
Бренд: MSI Страницы: 136
MSI B350 PC MATE Quick Start Manual preview
B350 PC MATE
Бренд: MSI Страницы: 134
Seco Qseven CQ7-A42 User Manual preview
Qseven CQ7-A42
Бренд: Seco Страницы: 49
OLIMEX ADuC-IO7020 User Manual preview
ADuC-IO7020
Бренд: OLIMEX Страницы: 14
Gigabyte GA-6RXB User Manual preview
GA-6RXB
Бренд: Gigabyte Страницы: 147
Xilinx XtremeDSP Spartan-3A DSP 3400A... User Manual preview
XtremeDSP Spartan-3A DSP 3400A...
Бренд: Xilinx Страницы: 50

Бренды по названию

Популярные бренды

Загрузить еще бренды