manualshive.com logo in svg

Yamaha F40H, Руководство пользователя

Поделиться
Скачать
Yamaha F40H Скачать руководство пользователя страница 71

Operation

64

EMU32852

Power trim and tilt models

The outboard motor can be tilted up partially
to allow operation in shallow water.

ECM00261

Do not tilt the outboard motor up so that
the cooling water inlet on the lower unit is
above the surface of the water when set-
ting up for and cruising in shallow water.
Otherwise severe damage from overheat-
ing can result.

EMU32914

Procedure for power trim and tilt models

(1) Place the remote control lever / gear

shift lever in neutral.

(2) Slightly tilt the outboard motor up to the

desired position using the power trim
and tilt switch. 

WARNING! Using the

power trim and tilt switch on the bot-
tom cowling while the boat is moving
or engine is on could increase the
risk of falling overboard and could
distract the operator, increasing the
risk of collision with another boat or
an obstacle.

 [EWM01851]

(3) To return the outboard motor to the nor-

ZMU03648

N

ZMU01771

UP

ZMU01935

6C1-9-7J-1E0.book  64 ページ  ２０１９年１０月３０日　水曜日　午後２時５６分

Содержание F40H















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды