Yamaha F40H Скачать руководство пользователя

Страница: 100 / 110

Trouble Recovery

(2) Put the engine in the desired position,

then tighten the manual valve screw by
turning it clockwise.

EMU41471

Water separator-alert indicator blinks
while cruising

EWM01501

Gasoline is highly flammable, and its va-
pors are flammable and explosive.



Do not perform this procedure on a hot
or running engine. Allow the engine to
cool.



There will be fuel in the fuel filter. Keep
away from sparks, cigarettes, flames or
other sources of ignition.



This procedure will allow some fuel to
spill. Catch fuel in a rag. Wipe up any
spilled fuel immediately.



The fuel filter must be reassembled
carefully with the O-ring, filter cup, and
hoses in place. Improper assembly or
replacement could result in a fuel leak,
which could result in a fire or explosion
hazard.

If the water separator-alert indicator on the
6Y8 Multifunction tachometer blinks, perform

the following procedure.

F40H, F50H, FT50J, F60F, FT60G
(1) Stop the engine.
(2) Remove the top cowling.
(3) Remove the plastic tie.

(4) Disconnect the water detection switch

coupler.

NOTICE:

Be careful not to get

any water on the water detection
switch coupler, otherwise a malfunc-
tion could occur.

[ECM01951]

1. Manual valve screw

ZMU03668

1. Water separator-alert indicator

1. Plastic tie

ZMU05441

ZMU07929

6C1-9-7J-1E0.book 93 ページ２０１９年１０月３０日　水曜日　午後２時５６分

Содержание F40H















































































































Результаты поиска

Содержание F40H

Отзывы:

Похожие инструкции для F40H

Бренды по названию

Популярные бренды

Yamaha F40H, Руководство пользователя

Результаты поиска

Содержание F40H

Отзывы:

Похожие инструкции для F40H

Бренды по названию

Популярные бренды