Yamaha F40H страница 102 Скачать руководство пользователя

Страница: 102 / 110

Trouble Recovery

(4) Remove the holder.

(5) Disconnect the water detection switch

coupler.

NOTICE:

Be careful not to get

any water on the water detection
switch coupler, otherwise a malfunc-
tion could occur.

[ECM01951]

(6) Unscrew the filter cup from the filter

housing.

NOTICE:

Be careful not to

twist the water detection switch lead
when unscrewing the filter cup.

[ECM01961]

(7) Drain the water in the filter cup by soak-

ing it up with a rag.

(8) Firmly screw the filter cup onto the filter

housing.

NOTICE:

Be careful not to

twist the water detection switch lead
when screwing the filter cup onto the
filter housing.

[ECM01971]

(9) Connect the water detection switch cou-

pler securely until a click is heard.

(10)Fasten the water detection switch lead

with the holder.

1. Holder

1. Water detection switch coupler

ZMU07095

ZMU07094

ZMU07096

1. Filter cup
2. Water detection switch lead

1. Water detection switch coupler

ZMU07097

ZMU07100

6C1-9-7J-1E0.book 95 ページ２０１９年１０月３０日　水曜日　午後２時５６分

Содержание F40H















































































































Результаты поиска

Содержание F40H

Отзывы:

Похожие инструкции для F40H

Бренды по названию

Популярные бренды

Yamaha F40H, Руководство пользователя

Результаты поиска

Содержание F40H

Отзывы:

Похожие инструкции для F40H

Бренды по названию

Популярные бренды