Yamaha F40G Скачать руководство пользователя

Страница: 98 / 110

Trouble Recovery

Q. Is fuel joint connection incorrect?
A. Connect correctly.

Q. Is heat range of spark plug incorrect?
A. Inspect spark plug and replace it with rec-
ommended type.

Q. Is high pressure fuel pump drive belt bro-
ken?
A. Have serviced by a Yamaha dealer.

Q. Is engine not responding properly to shift
lever position?
A. Have serviced by a Yamaha dealer.

Engine vibrates excessively.

Q. Is propeller damaged?
A. Have propeller repaired or replaced.

Q. Is propeller shaft damaged?
A. Have serviced by a Yamaha dealer.

Q. Are weeds or other foreign matter tangled
on propeller?
A. Remove and clean propeller.

Q. Is motor mounting bolt loose?
A. Tighten bolt.

Q. Is steering pivot loose or damaged?
A. Tighten or have serviced by a Yamaha
dealer.

EMU29435

Temporary action in

emergency

EMU29442

Impact damage

EWM00871

The outboard motor can be seriously
damaged by a collision while operating or
trailering. Damage could make the out-
board motor unsafe to operate.

If the outboard motor hits an object in the wa-
ter, follow the procedure below.

(1) Stop the engine immediately.
(2) Check the control system and all compo-

nents for damage. Also, check the boat
for damage.

(3) Whether damage is found or not, return

to the nearest harbor slowly and careful-
ly.

(4) Have a Yamaha dealer check the out-

board motor before operating it again.

EMU30684

Replacing fuse

If a fuse has blown, open the fuse holder and
remove the fuse with a fuse puller. Replace
it with a spare one of the proper amperage.

6C1-9-7J-1E0.book 91 ページ２０１９年１０月３０日　水曜日　午後２時５６分

Содержание F40G















































































































Результаты поиска

Содержание F40G

Отзывы:

Похожие инструкции для F40G

Бренды по названию

Популярные бренды

Yamaha F40G, Руководство пользователя

Результаты поиска

Содержание F40G

Отзывы:

Похожие инструкции для F40G

Бренды по названию

Популярные бренды