Yamaha F40G Скачать руководство пользователя

Страница: 107 / 110

INDEX

100

Identification numbers record ................. 5
Idle speed, inspecting ........................... 77
Impact damage ..................................... 91
Installation requirements....................... 14
Instruments and indicators.................... 31

Key number ............................................ 5

Laws and regulations.............................. 4
Low battery voltage-alert indicator........ 35
Low oil pressure alert............................ 40
Low oil pressure-alert indicator....... 31, 32
Lubrication ............................................ 69

Main switch ........................................... 25
Maintenance chart 1 ............................. 72
Maintenance chart 2 ............................. 75
Modifications........................................... 2
Mounting height .................................... 41
Mounting outboard motor...................... 14
Mounting the outboard motor................ 41
Muddy or acidic water........................... 17

Neutral interlock trigger......................... 22
Neutral throttle lever ............................. 22

Operating engine .................................. 49
Outboard motor disposal

requirements ...................................... 17

Outboard motor (painted surface),

checking ............................................. 70

Outboard motor safety ............................ 1
Outboard motor serial number................ 5
Overheat alert ....................................... 39
Overheat-alert indicator .................. 31, 33
Overloading ............................................ 3

Passengers............................................. 2
Passenger training.................................. 4
People in the water ................................. 2
Periodic maintenance ........................... 70
Personal flotation devices (PFDs) .......... 2
Power trim and tilt ................................... 1
Power trim and tilt switch (bottom

cowling) .............................................. 26

Power trim and tilt switch (remote

control or tiller handle) ........................ 26

Power trim and tilt system..................... 47
Power trim and tilt will not operate........ 92
Propeller ................................................. 1
Propeller, checking ............................... 81
Propeller, installing ............................... 82
Propeller, removing............................... 82
Propeller selection ................................ 14

Read manuals and labels ....................... 7
Remote control box............................... 21
Remote control lever............................. 22
Remote control requirements ............... 14
Replacement parts................................ 70
Replacing the engine oil filter................ 80
Rotating parts ......................................... 1

Sending fuel (portable tank).................. 49
Severe operating conditions ................. 71
Shallow water ....................................... 62
Shifting.................................................. 53
Shifting (checks after engine warm

up) ...................................................... 53

Spark plug, cleaning and adjusting....... 76
Specifications........................................ 12
Speedometer ........................................ 33
Starter will not operate.......................... 96
Start-in-gear protection ......................... 15
Starting engine...................................... 50
Steering friction adjuster ....................... 25
Stopping boat........................................ 55
Stopping engine.................................... 55

6C1-9-7J-1E0.book 100 ページ２０１９年１０月３０日　水曜日　午後２時５６分

Содержание F40G















































































































Результаты поиска

Содержание F40G

Отзывы:

Похожие инструкции для F40G

Бренды по названию

Популярные бренды

Yamaha F40G, Руководство пользователя

Результаты поиска

Содержание F40G

Отзывы:

Похожие инструкции для F40G

Бренды по названию

Популярные бренды