Yamaha F40G Скачать руководство пользователя | Manualshive

Страница: 28 / 110

background image

Components

21

EMU25831

Fuel joint

This joint is used to connect the fuel line.

EMU25842

Fuel gauge

This gauge is located on either the fuel tank
cap or on the fuel joint base. It shows the ap-
proximate amount of fuel remaining in the
tank.

EMU25851

Fuel tank cap

This cap seals the fuel tank. When removed,
the tank can be filled with fuel. To remove the
cap, turn it counterclockwise.

EMU25861

Air vent screw

This screw is on the fuel tank cap. To loosen
the screw, turn it counterclockwise.

EMU46751

Yamaha Security System (Y-COP)

ECM02461

The Yamaha Security System is sold in
conformity with the relevant laws and

regulations regarding radio wave trans-
mission. Therefore, if this product is used
outside the country where it was sold, it
may violate the laws or regulations re-
garding radio wave transmission in the
country it is used in. For details, consult
your Yamaha dealer.

The Yamaha Security System, which pro-
tects against theft, consists of the receiver
and remote control transmitters. The
Yamaha Security System is available from
your Yamaha dealer. For details, consult
your Yamaha dealer.

The engine cannot be started if the security
system is in the lock mode. The engine can
be started only in the unlock mode. For more
information, see the installation and owner’s
manual included with the security system.

TIP:

The security system cannot be used with
quad engine applications or Helm Master®.

EMU26182

Remote control box

The remote control lever actuates both the
shifter and the throttle. The electrical switch-
es are mounted on the remote control box.

1. Fuel joint
2. Fuel gauge
3. Fuel tank cap
4. Air vent screw

ZMU02284

3

1

4

2

1. Remote control transmitter
2. Receiver

2

1

6C1-9-7J-1E0.book 21 ページ２０１９年１０月３０日　水曜日　午後２時５６分

«
...
26
27
28
29
30
...
»

Содержание F40G















































































































Отзывы:

Нет отзывов

Похожие инструкции для F40G

Бренд: IEI Technology Страницы: 211

Бренд: IEI Technology Страницы: 8

Бренд: IEI Technology Страницы: 8

phyBOARD-Subra-i.MX6

Бренд: Phytec Страницы: 2

Бренд: Phytec Страницы: 128

Бренд: Sapphire Audio Страницы: 50

Бренд: MSI Страницы: 169

Бренд: ST Страницы: 24

Бренд: ASROCK Страницы: 198

Бренд: Gigabyte Страницы: 100

Бренд: MSI Страницы: 71

Бренд: Texas Instruments Страницы: 16

Бренд: Intel Страницы: 113

Бренд: JS Automation Страницы: 18

Бренд: Microchip Technology Страницы: 44

Бренд: WynMax Страницы: 68

LCMXO3L-DSI-EVN

Бренд: Lattice Страницы: 2

Бренд: Gigabyte Страницы: 39

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды