manualshive.com logo in svg

Yamaha E40G, Руководство по обслуживанию

Поделиться
Скачать
Yamaha E40G Скачать руководство пользователя страница 86

4.

Remove the washers, roller bearing and
connecting rod.

5.

Insert the support 

6

between crank 2

and 3 

7

with crank 3 on top. Place pres-

sure pin B 

8

on the shaft, and force it out

using a press.

6.

Remove the roller bearing 

9

from the

inner race 

0

.

7.

Remove the crankpin between cranks 2
and 3 by applying pressure to pressure
pin C using a press.

NOTE:

Pressure pin C should be pressed down
straight.

POWR

5-31

6F65G11

Power unit

Plate C 

1

: 90890-02402 

Pressure pin C 

4

: 90890-02403

2.

Insert the plate C 

1

between crank 1 

2

and crank 2 

3

. Place pressure pin C 

4

in the end of the crank pin 

5

.

NOTE:

Remove the bearing before starting this pro-
cedures.

3.

Remove the crank pin by applying pres-
sure to pressure pin C 

4

with a press.

c

C

9

Apply pressure to pressure pin C 
slowly.

9

Hold pressure pin C in line with the
press screw spindle.

NOTE:

9

When forcing out the crank pin, use care so
that the crank does not fall.

9

To remove crank 4, follow the same proce-
dure.

6B450550

1

3

2

4

5

6F650470

9

0

6B450560

Plate C 

1

: 90890-02402 

Pressure pin C 

4

: 90890-02403

Support 

6

: 90890-02394 

Pressure pin B 

8

: 90890-02390

Содержание E40G









































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды