Yamaha E40G Скачать руководство пользователя страница 195

Страница: 195 / 200

6F65G11

9-8

Electrical

Starting system (continued from previous page)

Disassemble and check the
starter motor.

Yes

Check the starter relay for
continuity.

Replace the starter relay.

Is there continuity?

Symptom: The battery loses power quickly. (WH, W)

Be sure the electrolyte level and gravity are specific condition.

Be sure the wireharness, couplers and connectores are good connection.

Charging system

Check the lighting coil output
peak voltage.

Check the rectifier output peak
voltage.

Replace the battery, and then
check the all of the electrical
equipment on the boat.

Replace the lighting coil.

Replace the rectifier.

Does the out-
put peak voltage
exceed specifi-
cation values?

Yes

Does the out-
put peak voltage
exceed specifi-
cation values?

Yes

Содержание E40G









































































































































































































Результаты поиска

Содержание E40G

Отзывы:

Бренды по названию

Популярные бренды

Yamaha E40G, Руководство по обслуживанию

Результаты поиска

Содержание E40G

Отзывы:

Бренды по названию

Популярные бренды