Yamaha E40G Скачать руководство пользователя страница 36

Страница: 36 / 200

Check that the neutral switch under the
start-in-protection lever

is pushing the

neutral switch

. (WH)

Checking the gear shift operation
(W)

Check that the gear shift operates
smoothly when shifting it from neutral to
forward or reverse. Adjust the shift cable
length if necessary.

Set the gear shift to the neutral position.

Remove the cable joint

, and then dis-

connect the shift cable

Set the shift lever

to the neutral posi-

tion.

Adjust the position of the cable end

until it is aligned with the hole of the shift
lever.

The shift/throttle cable end must be
screwed in a minimum of 8.0 mm (0.31 in)

Install the cable joint and tighten the
adjusting nut.

Check the gear shift for smooth operation
and, if necessary, repeat steps 2—6.

Checking the engine idle speed

Start the engine and warm it up for 5 min-
utes.

Attach the special service tool to spark
plug wire #1

, and then check the

engine idle speed. Adjust if out of specifi-
cation.

CHK

ADJ

3-7

6F65G11

Periodic checks and adjustments

6F610077

F,R

6F630120

6F630135

Digital tachometer: 90890-06760

Engine idle speed:

1,100—1,200 r/min

6F630160

Содержание E40G









































































































































































































Результаты поиска

Содержание E40G

Отзывы:

Бренды по названию

Популярные бренды

Yamaha E40G, Руководство по обслуживанию

Результаты поиска

Содержание E40G

Отзывы:

Бренды по названию

Популярные бренды