Yamaha E40G Скачать руководство пользователя страница 33

Страница: 33 / 200

6F65G11

3-4

Checking the thermostat

Remove the thermostat cover

, gasket

, and thermostat

Suspend the thermostat in a container of
water.

Place a thermometer in the water and
slowly heat the water.

Check the thermostat valve opening at
the specified water temperatures.
Replace if out of specification.

Install the thermostat and thermostat
cover, and then tighten the cover bolts.

Checking the cooling water pas-
sages

Check the cooling water inlet cover

screw

and cooling water inlet for clog-

ging. Clean if necessary.

E40G

∫

E40J

Place the lower unit in water, then start
the engine.

Check for water flow at the cooling water
pilot hole. If there is no water flow, check
the cooling water passage inside the out-
board motor.

6B430060

6F630040

6B430070

Fuel system/Power unit

Water

Valve lift

temperature

58–62°C

0 mm (0 in)

(136–147°F)

(valve begins to tilt)

above

more than

70°C (158°F)

3.0 mm (0.12 in)

6F630060

6F630070

∫

6F610170

Содержание E40G









































































































































































































Результаты поиска

Содержание E40G

Отзывы:

Бренды по названию

Популярные бренды

Yamaha E40G, Руководство по обслуживанию

Результаты поиска

Содержание E40G

Отзывы:

Бренды по названию

Популярные бренды