manualshive.com logo in svg

Yamaha E40G, Руководство по обслуживанию

Поделиться
Скачать
Yamaha E40G Скачать руководство пользователя страница 137

6F65G11

6-40

9

8

7

6

5

4

3

2

1

Drive shaft  and lower case

Assembling the oil seal housing

1.

Apply grease to new oil seals, and then
install them into the oil seal housing.

Assembling the lower case

1.

Install the needle bearing into the lower
case to the specified depth.

NOTE:

9

Install the needle bearing with the manufac-
ture identification mark 

a

facing up.

9

Be careful not to let the stopper 

b

get out

of position when using the driver rod SL.

2.

Install the sleeve, original shim(s), and
drive shaft bearing outer race.

c

C

Add or remove shim(s), if necessary, if
replacing the pinion or lower case.

NOTE:

9

Apply gear oil to the inside and outside of
the sleeve before installation.

9

Install the sleeve with the projection 

d

fac-

ing forward.

3.

Install the original shim(s) and taper roller
bearing outer race.

c

C

Add or remove shim(s), if necessary, if
replacing the forward gear or lower case.

2

1

6F660270

G

6B460350

7

6

5

4

5

4

d

6F660290

Ball bearing attachment 

1

:

90890-06653

Driver rod L3 

2

: 90890-06652

Bearing outer race attachment 

4

:

90890-06627

Driver rod LS 

5

: 90890-06606

Bearing outer race attachment 

6

:

90890-06622

Driver rod LL

7

: 90890-06605

Driver rod SL

1

: 90890-06602

Needle bearing attachment 

2

: 

90890-06614

Bearing depth plate

3

: 90890-06603

Depth 

c

: 

182.5 — 183.0 mm 
(7.19 — 7.20 in)

Содержание E40G









































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды