Yamaha DTXTREME III, Руководство пользователя

Страница: 75 / 160

Basic Structure of the DTXTREME III
Reference
DTXTREME III Owner’s Manual 75
Dr
um Kit mode
Ref
erence
Song mode
Clic
k mode
Tr
igger mode
File mode
Utility mode
Chain mode
Sampling mode
*1 The Bottom parameter is available only when the value is less than
that of the Top parameter.
*2 The Color parameter may not be effective depending on the values
of the Mode and Stage parameters.
*3 The Top parameter is available only when the value is more than that
of the Bottom parameter.
NoisModDpt Determines the depth of the noise modulation.
NoisModSpd Determines the speed of the noise modulation.
NoisTon Determines the characteristics of the noise.
On/Off Turns the isolator on or off.
OSCFrqCors
Determines the frequency for modulating the input
wave.
OSCFrqFine
Finely determines the frequency for modulating the
input wave.
OutGain Determines the level gain.
OutLvl Determines the output level.
OutLvl1 Determines the output level for the 1st series.
OutLvl2 Determines the output level for the 2nd series.
Output Determines the output level.
OverDr
Determines the degree and character of the distor-
tion effect.
Pan1 Determines the pan position for the 1st series.
Pan2 Determines the pan position for the 2nd series.
PanAEGLvl
This parameter of the Slice effect determines the
minimum level of the AEG applied to the panned
sound.
PanAEGType
This parameter of the Slice effect determines the
type of the AEG applied to the panned sound
PanDirectn Determines the type of the Auto Pan.
PanDpth Determines the depth of the pan effect.
PanType Determines the pan type.
PhShiftOfst Determines the offset value of the phase modulation.
Pitch1 Determines the pitch in semitones for the 1st series.
Pitch2 Determines the pitch in semitones for the 2nd series.
PMDepth Determines the depth of the pitch modulation.
Pre-LPF
Determines the Cutoff frequency of the Low Pass Fil-
ter before the modulation.
PreLPFReso
Determines the Resonance of the Low Pass Filter for
the input sound.
PreModHPF
Determines the Cutoff frequency of the High Pass
Filter before the modulation.
Presenc
This guitar amp effect parameter controls the high
frequencies.
Ratio Determines the ratio of the compressor.
RelCurv
Determines the release curve of the envelope fol-
lower.
Release
Determines the amount of time that elapses between
the release or end of a sound and the end of the
compressor effect.
RelTime Determines the release time of the envelope follower.
Reso Determines the resonance of the filter.
ResoOfst Determines the resonance as offset.
RevDly
Determines the delay time from the early reflections
until the reverberations.
RevTime Determines the reverb time.
RoomSize Determines the room capacity.
Rotor/Horn
Determines the volume balance of the horn and
rotor.
RotorF
Determines the speed of the rotor when the slow/fast
switch is set to “fast.”
RotorS
Determines the speed of the rotor when the slow/fast
switch is set to “slow.”
Sens
[For FLANGER&PHASER effects, TECH effects]
Determines the sensitivity of the modulation applied
to the input change.
[For TOUCH WAH]
Determines the sensitivity of the wah filter’s change
applied to the input change.
S-FTmHorn
Determines how long it takes for the rotation speed of
the horn to change from the current speed (slow or
fast) to another speed (fast or slow) when the rotation
speed is switched.
Paramater
name
Descriptions
S-FTmRotor
Determines how long it takes for the rotation speed of
the rotor to change from the current speed (slow or
fast) to the another speed (fast or slow) when the
rotation speed is switched.
SmplFrqCtr Controls the sampling frequency.
SpcType Selects the type of space simulation.
Speaker Selects the type of speaker simulation.
Speed
[For FLANGER]
Determines the frequency of the LFO wave which
controls the cyclic change of the delay modulation.
[For PHASER MONO, PHASER STEREO]
Determines the frequency of the LFO wave which
controls the cyclic change of the phase modulation.
[For AUTO WAH]
Determines the speed of the LFO.
SpeedCtrl Switches the rotary speed.
Spread Determines the spread of the sound.
Stage Determines the step number of the phase shifter.
Thresh
Determines the minimum input level at which the
effect is applied.
Top
*3
Determines the maximum value of the wah filter.
Type
[For FLANGER]
Determines the type of flanger.
[For WAH effects]
Determines the type of Wah.
[For EARLY REFLECTION]
Determines the type of the reflection sound.
Vowel Selects a vowel type.
WallVary
Determines the wall status of the simulated room.
Higher settings produces more diffuse reflections.
Width Determines the width of the simulated room.
WordLen
Determines the resolution of the sound, or how
“rough” the sound is.
Paramater
name
Descriptions