background image

DME Setup Manual

• For more details regarding a specific DME unit, please refer to the manual supplied with the unit in question, and for more details regarding the DME Designer application, please refer to the DME Designer manual (pdf).

• Please note that, within this document, the term “DME” refers to the DME64N and DME24N, while the term “DME Satellite” refers to the DME8i-C, DME8o-C, DME4io-C, DME8i-ES, DME8o-ES, and DME4io-ES

This manual describes the process of setting up a DME system, from making the initial DME unit settings (DME64N / 

DME24N / DME8i-C / DME8o-C / DME4io-C / DME8i-ES /DME8o-ES / DME4io-ES) to synchronizing with the DME 

Designer application installed on a computer.

page 

02

page 

04

page 

08

1-1. Install DME Designer and DME-N Network Driver
1-2. Install the USB-MIDI Driver

page 

13

Setting up DME64N/24N 
Networks via 
Panel Operations

This section explains how to setup networks directly 
from a DME64N/24N.

page 

13

Related web site on DME 
Units and peripherals

This section serves as a guide to online 
information on Speaker Processor Components 
library data, optional cards, and touch-panel 
controllers (AMX/Creston).

page 

13

Connecting to 
External Devices

This section covers connection to 
remote controllers via Ethernet 
or GPI.

page 

16

Troubleshooting & Tips Chart

This chart serves as a quick guide to the steps that should be taken to 
ensure correct operation of DME units.

page 

14

Appendix:
Detailed DME-N Network Driver settings 

Connecting 

a single DME unit

 

directly to a computer via USB cable

● 

Setting up DME cards 

(only when expansion cards will be used)

● 

Configuring components and Writing configurations

● 

Going Online and Checking sound output

● 

DME setup

● 

Changing the computer's IP address settings

● 

Setting the DME-N Network Driver

● 

Connecting with DME Designer

 

Connecting 

multiple DME units

 

to a computer via Ethernet cables

Connecting Computer and DME unit 

This sections covers procedures for either connecting a single DME unit to a computer or connecting multiple DME units to 

a computer within the same subnet. 

4. In-depth Information on DME Units 

1. Installing the Software

2. Basic Setup

3. Advanced Setup

Содержание DME Series

















Отзывы: