Yamaha 30DMH Скачать руководство пользователя | Manualshive

Страница: 39 / 66

background image

Operation

34

clip from the engine shut-off switch.

EMU27862

Trimming outboard motor

WARNING

EWM00740

Excessive trim for the operating condi-
tions (either trim up or trim down) can
cause boat instability and can make
steering the boat more difficult. This in-
creases the possibility of an accident. If
the boat begins to feel unstable or is hard
to steer, slow down and/or readjust the

trim angle.

The trim angle of the outboard motor helps
determine the position of the bow of the boat
in the water. Correct trim angle will help im-
prove performance and fuel economy while
reducing strain on the engine. Correct trim
angle depends upon the combination of
boat, engine, and propeller. Correct trim is
also affected by variables such as the load in
the boat, sea conditions, and running speed.

EMU27872

Adjusting trim angle for manual tilt
models

There are 4 or 5 holes provided in the clamp
bracket to adjust the outboard motor trim an-
gle.
1.

Stop the engine.

2.

Tilt the outboard motor up, and then re-
move the trim rod from the clamp brack-
et.

1. Trim operating angle

ZMU02858

1

«
...
37
38
39
40
41
...
»

Содержание 30DMH



































































Отзывы:

Нет отзывов

Похожие инструкции для 30DMH

Бренд: DFI Страницы: 39

Бренд: ON Semiconductor Страницы: 5

Бренд: ST Страницы: 77

Бренд: AOpen Страницы: 8

Бренд: IEI Technology Страницы: 17

C5535 DSPShield

Бренд: Texas Instruments Страницы: 49

Бренд: Texas Instruments Страницы: 14

Linear DC2681A-A

Бренд: Analog Devices Страницы: 8

Бренд: ECS Страницы: 74

Бренд: Supero Страницы: 78

Бренд: Gigabyte Страницы: 96

Бренд: Supermicro Страницы: 84

dsPICDEM MCHV-3

Бренд: Microchip Technology Страницы: 68

Бренд: ST Страницы: 52

Бренд: Icop Страницы: 41

PHANTOM GAMING X670E PG Lightning

Бренд: ASROCK Страницы: 66

LANParty Jr. GF9400 T2RS

Бренд: DFI Страницы: 138

Бренд: AOpen Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды