Yamaha 30DMH Скачать руководство пользователя | Manualshive

Страница: 22 / 66

background image

Components

17

partially to provide more clearance when op-
erating in shallow water.

EMU30530

Tilt lock mechanism

The tilt lock mechanism is used to prevent
the outboard motor from lifting out of the wa-
ter when in reverse gear.

To lock it, set the tilt lock lever in the lock po-
sition. To release, push the tilt lock lever in
the release position.

EMU26351

Tilt support lever for manual tilt
model

To keep the outboard motor in the tilted up
position, lock the tilt support lever to the
swivel bracket.

NOTICE

ECM00660

Do not use the tilt support lever or knob
when trailering the boat. The outboard
motor could shake loose from the tilt sup-
port and fall. If the motor cannot be trail-
ered in the normal running position, use
an additional support device to secure it

in the tilt position.

EMU26372

Top cowling lock lever(s) (turn type)

To remove the engine top cowling, turn the
lock lever(s) and lift off the cowling. When in-
stalling the cowling, check to be sure it fits
properly in the rubber seal. Then lock the
cowling again by returning the lever(s) to the
lock position.

1. Tilt lock lever

ZMU03763

1

ZMU03764

1. Top cowling lock lever(s)

ZMU03766

ZMU03701

1

«
...
20
21
22
23
24
...
»

Содержание 30DMH



































































Отзывы:

Нет отзывов

Похожие инструкции для 30DMH

Бренд: Mercury Страницы: 41

Бренд: NXP Semiconductors Страницы: 12

Бренд: JETWAY Страницы: 52

Бренд: Renesas Страницы: 17

Spartan-7 SP701

Бренд: Xilinx Страницы: 4

Бренд: Gigabyte Страницы: 104

Бренд: Renesas Страницы: 2

STEVAL-LLL002V1

Бренд: STMicroelectronics Страницы: 29

Бренд: California Eastern Laboratories Страницы: 34

TLE986 Evalboard Series

Бренд: Infineon Страницы: 20

Бренд: MSI Страницы: 32

Бренд: Watersnake Страницы: 20

SUPER i2DMR-8G2

Бренд: Supero Страницы: 78

Бренд: One Control Страницы: 8

Бренд: Silicon Laboratories Страницы: 12

Бренд: MSI Страницы: 137

SMART SPMXCA200

Бренд: Spektrum Страницы: 16

Бренд: Altera Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды