Yamaha 30DMH Скачать руководство пользователя | Manualshive

Страница: 37 / 66

background image

Operation

32

shut-off switch.

EMU34550

Shifting

WARNING

EWM00180

Before shifting, make sure there are no
swimmers or obstacles in the water near

you.

NOTICE

ECM01610

Warm up the engine before shifting into
gear. Until the engine is warm, the idle
speed may be higher than normal. High
idle speed can prevent you from shifting
back to neutral. If this occurs, stop the
engine, shift to neutral, then restart the

engine and allow it to warm up.

To shift out of neutral
1.

Move the gear shift lever firmly and
crisply forward (for forward gear) or
backward (for reverse gear). Be sure to
check that the tilt lock lever is in the lock/
down position (if equipped) before oper-
ating in reverse.

To shift from in gear (forward/reverse) to
neutral
1.

Close the throttle so that the engine
slows to idle speed.

2.

After the engine is at idle speed in gear
move the gear shift lever firmly and
crisply into the neutral position.

ZMU03788

R

N

F

ZMU05678

ZMU02030

N

ZMU03724

«
...
35
36
37
38
39
...
»

Содержание 30DMH



































































Отзывы:

Нет отзывов

Похожие инструкции для 30DMH

Бренд: Giada Страницы: 2

BLKDP55WG - P55 LG1156 MAX-16 GB DDR3 ATX Motherboard

Бренд: Intel Страницы: 88

Бренд: C-Control Страницы: 8

Strata Enabled NCV6357

Бренд: ON Semiconductor Страницы: 6

Бренд: BCM Страницы: 3

Бренд: Advantech Страницы: 82

Бренд: VIA Technologies Страницы: 86

Бренд: NXP Semiconductors Страницы: 40

Бренд: ASROCK Страницы: 200

Бренд: Texas Instruments Страницы: 44

Бренд: Biostar Страницы: 40

Бренд: Wolfson Страницы: 12

RouterBOARD M11 Series

Бренд: MikroTik Страницы: 3

Бренд: Yamaha Страницы: 87

Бренд: Yamaha Страницы: 81

Бренд: Yamaha Страницы: 90

Бренд: Yamaha Страницы: 90

Бренд: Yamaha Страницы: 106

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды