Yamaha 30DMH Скачать руководство пользователя | Manualshive

Страница: 36 / 66

background image

Operation

31

TIP:

●

When the engine is cold, it needs to be
warmed up. For further information, see
page 31.

●

If the engine does not start on the first try,
repeat the procedure. If the engine fails to
start after 4 or 5 tries, open the throttle a
small amount (between 1/8 and 1/4) and
try again. Also if the engine is warm and
fails to start, open the throttle a same
amount and try to start the engine again. If
the engine still fails to start, see page 54.

EMU36510

Checks after starting engine

EMU36520

Cooling water

Check for a steady flow of water from the
cooling water pilot hole. A continuous flow of
water from the pilot hole shows that the wa-
ter pump is pumping water through the cool-
ing passages. If the cooling passages are
frozen, it may take a while for water to start
flowing out of the pilot hole.

NOTICE

ECM01810

If water is not flowing out of the pilot hole
at all times while the engine is running,
overheating and serious damage could
occur. Stop the engine and check wheth-
er the cooling water inlet on the lower
case or the cooling water pilot hole is

blocked. Consult your Yamaha dealer if
the problem cannot be located and cor-

rected.

Check that no water leaks from the joints be-
tween the exhaust cover, cylinder head, and
body cylinder.

EMU27670

Warming up engine

EMU27683

Choke start models

After starting the engine, allow it to idle for 3
minutes to warm up. Failure to do so will
shorten engine life. Gradually return the
choke knob to its home position as the en-
gine warms up.

EMU36530

Checks after engine warm-up

EMU36540

Shifting

While tightly moored, and without applying
throttle, confirm that the engine shifts
smoothly into forward and reverse, and back
to neutral.

EMU36970

Stop switches

●

Press the engine stop button and make
sure the engine stops.

●

Confirm that removing the clip from the en-
gine shut-off switch stops the engine.

●

Confirm that the engine cannot be started
with the clip removed from the engine

ZMU02030

ZMU02856

«
...
34
35
36
37
38
...
»

Содержание 30DMH



































































Отзывы:

Нет отзывов

Похожие инструкции для 30DMH

Бренд: MSI Страницы: 76

Бренд: ST Страницы: 11

Бренд: NXP Semiconductors Страницы: 28

Бренд: NXP Semiconductors Страницы: 16

Бренд: Texas Instruments Страницы: 17

Бренд: Texas Instruments Страницы: 24

Бренд: Biostar Страницы: 51

Бренд: Texas Instruments Страницы: 21

IONITX-N series

Бренд: Zotac Страницы: 50

VECTOR 1 MOTHERBOARD

Бренд: Vector Graphic Страницы: 14

Бренд: JETWAY Страницы: 19

Бренд: AOpen Страницы: 8

Бренд: TYAN Страницы: 47

Бренд: Global American Страницы: 37

Бренд: Gigabyte Страницы: 93

Бренд: National Semiconductor Страницы: 22

Бренд: Acorp Страницы: 4

Бренд: Gigabyte Страницы: 88

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды