manualshive.com logo in svg

Yamaha 2006 FJR1300AS, Руководство по обслуживанию

Поделиться
Скачать
Yamaha 2006 FJR1300AS Скачать руководство пользователя страница 99

YCC-S (Yamaha Chip Controlled-Shift) SYSTEM

– 90 –

The transmission gear display on the multi-function meter fails to indicate the selected gear.
 

 NG

 →

OK

 ↓

 

 NG

 →

OK

 ↓

ET2D21021

MAINTENANCE OF THE MCU

Checking the MCU

1. Check:

• Terminals “1” of the MCU

Cracks/damages 

→

 Replace the MCU.

• Terminals “2” of the MCU couplers

Connection defective, contaminated, come-
off 

→

 Correct or clean.

NOTE:

If the MCU couplers are clogged with mud or dirt, 
clean with compressed air.

ET2D21028

MCU (motor control unit) SELF-DIAGNOSTIC FUNCTION

The MCU (motor control unit) is equipped with a self-diagnostic function in order to ensure that the 
YCC-S system is operating normally. If this function detects a malfunction in the YCC-S system, it im-
mediately operates the system under substitute characteristics and lights the YCC-S indicator and 
warning light to alert the rider that a malfunction has occurred in the system. Once a malfunction has 
been detected, a fault code is stored in the memory of the MCU (motor control unit). After the engine 
has been stopped, the lowest fault code number appears on the odometer/tripmeter/fuel reserve trip-
meter LCD. Once a fault code has been displayed, it remains stored in the memory of the MCU (motor 
control unit) until it is deleted.

NOTE:

If the engine trouble indicator “1”, YCC-S indicator “2”, and engine trouble warning light “3” all come on, 
malfunctions have been detected in both the fuel injection system and the YCC-S system. If this occurs, 
the fault codes for the fuel injection system take priority over those for the YCC-S system, so only the 
fuel injection system fault codes will appear in the multi-function display. The fault codes for the YCC-
S system will be displayed in the multi-function display after all of the fault codes for the fuel injection 
system have been deleted using the reinstatement method.

1. Check the gear position sensor.

Refer to “CHECKING THE GEAR 
POSITION SENSOR” on page 132 
and “ADJUSTING THE GEAR PO-
SITION SENSOR” on page 50.

Replace the gear position sensor.

2. Check the gear position setting.

Refer to “Diagnostic code table (Di-
agnostic code No. Sh_ _65)”.

Replace the MCU (motor control unit).

Replace the meter assembly.

1

2

Содержание 2006 FJR1300AS























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды