manualshive.com logo in svg

Yamaha 2006 FJR1300AS, Руководство по обслуживанию

Поделиться
Скачать
Yamaha 2006 FJR1300AS Скачать руководство пользователя страница 121

YCC-S (Yamaha Chip Controlled-Shift) SYSTEM

– 112 –

Fault code No.

Sh_ _34

Symptom

TPS (throttle position sensor) signal is abnor-
mal.

Order Item/components and probable 

cause

Check or maintenance job

Reinstatement 
method

1

Connections
• Wire harness MCU (motor control 

unit) coupler

• Wire harness ECU coupler

• Check the coupler for any pins 

that may be pulled out.

• Check the locking condition of 

the coupler.

• If there is a malfunction, repair it 

and connect the coupler se-
curely.

Repairing the 
cause of the 
malfunction.

2

Open or short circuit in wire harness.

• Repair or replace if there is an 

open or short circuit.

• Between ECU coupler and 

MCU (motor control unit) cou-
pler.
(yellow/blue–yellow/blue)

Fault code No.

Sh_ _35

Symptom

Start switch signal is abnormal.

Order Item/components and probable 

cause

Check or maintenance job

Reinstatement 
method

1

Connections
• Wire harness MCU (motor control 

unit) coupler

• Relay unit coupler
• Right handlebar switch coupler

• Check the coupler for any pins 

that may be pulled out.

• Check the locking condition of 

the coupler.

• If there is a malfunction, repair it 

and connect the coupler se-
curely.

Repairing the 
cause of the 
malfunction.

2

Open or short circuit in wire harness 
and/or front cowling wire harness.

• Repair or replace if there is an 

open or short circuit.

• Between right handlebar switch 

coupler and relay unit coupler.
(white/blue–white/blue)

• Between relay unit coupler and 

MCU (motor control unit) cou-
pler.
(blue/white–blue/white)

3

Defective relay unit.

• Check and replace relay unit.

Refer to “CHECKING THE RE-
LAYS” in chapter 8. (Manual 
No.: 3P6-28197-E0)

4

Defective start switch.

• Check and replace right handle-

bar switch.
Refer to “CHECKING THE 
SWITCHES” in chapter 8. 
(Manual No.: 3P6-28197-E0)

Содержание 2006 FJR1300AS























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды