Yale Lodeking LT Series Скачать руководство пользователя

Страница: 10 / 53

HOIST

OPERATION & MAINTENANCE

P/N: 11854801 REV. AC

September 2017

COLUMBUS

McKINNON

C O R P O R A T I ON

Columbus McKinnon Corporation

Amherst, NY USA

NOTICE TO PERSONS RECEIVING THIS DRAWING AND/OR TECHNICAL INFOR

MATION

2/3/2015

APCCE

45487403

1:16

HOIST ASSEMBLY

200MM WHEEL BLOCKS

15T LODEKING LT

RSMS

Modeled:
Drawn:
Approved:
Design Authority:
Original project:
Original scale:

Format

Number:

Hoist PDE
Hoist PDE

2/3/2015

Dimensional Units

INCH

Sheet

Third Angle Projection

Description:

-
-

ECN

-
Rev.

Description of change

Date

Material:

Columbus McKinnon Corporation

Hoist & Rigging - Americas

Amherst, NY USA

Material No:

Standard:

Standard Dimensional

Tolerances Unless

Otherwise Specified

0" to 60" Over 60"

.X .020 .025

.XX .010 .015

.XXX .005 .010

Ang 0 30' 0 30'

Columbus McKinnon Corporation (CMCO) claims proprietary rights

in the material disclosed hereon. This drawing and/or technica

l information is issued in

confidence for engineering information only and may not be repr

oduced or used to manufacture anything shown or referred to her

eon without direct

permission from CMCO to the user. This drawing and/or technica

l information is loaned for mutual assistance and is subject to

recall by CMCO at any time.

This drawing and/or technical information is the property of CM

CO.

COLUMBUS

McKINNON

C O R P O R A T I ON

Columbus McKinnon Corporation

Amherst, NY USA

NOTICE TO PERSONS RECEIVING THIS DRAWING AND/OR TECHNICAL INFOR

MATION

2/3/2015

APCCE

45487403

1:24

HOIST ASSEMBLY

200MM WHEEL BLOCKS

15T LODEKING LT

RSMS

Modeled:
Drawn:
Approved:
Design Authority:
Original project:
Original scale:

Format

Number:

Hoist PDE
Hoist PDE

2/3/2015

Dimensional Units

INCH

Sheet

Third Angle Projection

Description:

-
-

ECN

-
Rev.

Description of change

Date

Material:

Columbus McKinnon Corporation

Hoist & Rigging - Americas

Amherst, NY USA

Material No:

Standard:

Standard Dimensional

Tolerances Unless

Otherwise Specified

0" to 60" Over 60"

.X .020 .025

.XX .010 .015

.XXX .005 .010

Ang 0 30' 0 30'

Columbus McKinnon Corporation (CMCO) claims proprietary rights

in the material disclosed hereon. This drawing and/or technica

l information is issued in

confidence for engineering information only and may not be repr

oduced or used to manufacture anything shown or referred to her

eon without direct

permission from CMCO to the user. This drawing and/or technica

l information is loaned for mutual assistance and is subject to

recall by CMCO at any time.

This drawing and/or technical information is the property of CM

CO.

REEVING TYPES

Yale powered wire rope hoists and winches are reeved in various

ways to gain desired advantages. Proper reeving insures maximum

life of the hoist drum, wire rope, and bottom block assembly while

obtaining the best characteristics of capacity, lift, and speed for the

basic unit.

Reeving is “double”, i.e. two ropes coming from the drum. Close

headroom hoists are double reeved. “Part” designates the number

of times the rope runs between the hoist and bottom block.

For example: With 2 part double reeving, the rope runs from the rope

drum to the bottom block, up to the equalizer sheave, back to the

bottom block, then back to the rope drum, indicating 4 “parts” of

rope supporting the load.

The drawings below show the characteristics of each principal

method of reeving.

Advantages of double reeved units include minimum lateral hook

drift (keeping load in the same approximate position in relation to

the drum and beam) and a lower hoist headroom requirement.

4 PART REEVING

10 TON CAPACITY

8 PART REEVING

20 & 25 TON CAPACITY

6 PART REEVING

15 TON CAPACITY

Содержание Lodeking LT Series





















































Результаты поиска

Содержание Lodeking LT Series

Отзывы:

Похожие инструкции для Lodeking LT Series

Бренды по названию

Популярные бренды

Yale Lodeking LT Series, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание Lodeking LT Series

Отзывы:

Похожие инструкции для Lodeking LT Series

Бренды по названию

Популярные бренды