Yale Lodeking LT Series страница 46 Скачать руководство пользователя

Страница: 46 / 53

TROLLEY

OPERATION & MAINTENANCE

P/N: 11854801 REV. AC

September 2017

15T LOWER BLOCK ASSEMBLY

Item Number

Description

Quantitiy

Part Number

Hook

23615401

Latch Kit

23556301

Roll Pin

10171654

Lower Block Weldment

33356301

SHCS

11852808

Lock Washer

11852809

Staking Plate

11839401

Thrust Bearing

23554300

Thrust Washer

23554100

Hook Nut

23554401

Sheave Pin

23622501

Sheave Plate Flathead Bolts

11852843

Outer Sheave Spacer

23637601

Sheave Bearing

10377714

Running Sheave

33370401

Sheave Plate

23637401

Inner Sheave Spacer

23637605

Cover Bolts

11852816

Block Colver

23622801

Yale Logo Tag

23391502

Capacity Tag

23391555

COLUMBUS

McKINNON

C O R P O R A T I ON

NOTICE TO PERSONS RECEIVING THIS DRAWING AND/OR TECHNICAL INFOR

MATION

Columbus McKinnon Corporation

Amherst, NY USA

-
-
Date

Rev.

-
ECN

Description:

Third Angle Projection

Sheet

Standard Dimensional

Tolerances Unless

Otherwise Specified

INCH

Dimensional Units

2/13/2013

Hoist PDE

Wadesboro

Number:

Format

Original scale:

Original project:

Design Authority:

Approved:

Drawn:

Modeled:

RSMS

15T LOWER BLOCK ASSEMBLY

1:4

APCCE

2/10/2015

Description of change

-
-
-

D6 REEVE

LODEKING LT

Standard:
Material No:

Columbus McKinnon Corporation

Hoist & Rigging - Americas

Amherst, NY USA

Material:

0" to 60" Over 60"

.X .020 .025

.XX .010 .015

.XXX .005 .010

Ang 0 30' 0 30'

Columbus McKinnon Corporation (CMCO) claims proprietary rights

in the material disclosed hereon. This drawing and/or technical

information is issued in

confidence for engineering information only and may not be repr

oduced or used to manufacture anything shown or referred to her

eon without direct

permission from CMCO to the user. This drawing and/or technical

information is loaned for mutual assistance and is subject to

recall by CMCO at any time.

This drawing and/or technical information is the property of CM

CO.

23577202

FIGURE 16

Содержание Lodeking LT Series





















































Результаты поиска

Содержание Lodeking LT Series

Отзывы:

Похожие инструкции для Lodeking LT Series

Бренды по названию

Популярные бренды

Yale Lodeking LT Series, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание Lodeking LT Series

Отзывы:

Похожие инструкции для Lodeking LT Series

Бренды по названию

Популярные бренды