23
9
Keyfob remote control accessory
Programming
Learn in the keyfob as follows:
1
Enter the D/- menu and select the Add
Device sub menu.
2
Press the Arm button on the keyfob remote when
prompted and confirm it is the correct detector
by pressing OK.
3
After you have assigned a zone number for the
keyfob remote, you are presented with a choice:
¥ Medical Emg : Control unit dials a medical
emergency alarm when the Panic button on the
keyfob remote is pressed.
¥ Personal Att : Control unit dials a personal attack
alarm when the Panic button is pressed.
4
Press OK. You can now choose latch reporting.
¥ Latch.Rpt.Off : No keyfob reporting of arming
status to the Intamac Home Manager
TM
Service,
this is set as factory default.
¥ Latch.Rpt.On : This will report every time the Home
is armed, Away armed and disarmed by the keyfob.
5
Press OK. You are now asked to choose a user
number. If latch reporting is used this is needed
by the control unit to identify who is arming and
disarming the system.
¥ User - : This is used if latch reporting is not
required, or if you do not want the user to be
individually identified.
¥ User 1 to User 6 : Use arrow keys to choose user
number. If you want to identify a latch reporting user
then a number can be assigned. This can be the
same as User PIN code number, for example if
Frank is using PIN code 3456 and is user 3, then
a keyfob can be similarly named Frank and be
assigned user 3 as well. This will identify Frank
every time he arms or disarms with either his keyfob
or 3456 PIN code.
6
Press OK. Enter a name of your choice.
7
Press OK and the display will show your
selection, press OK again to confirm or
to start
again
¥ The Panic button has to be pressed for more
than 5 seconds to operate. This is a safety
feature to stop accidental operation.
¥ If programmed as a Personal Attack alarm, an
alarm started by the Panic button cannot be
silenced with the keyfob remote, only with the
control unit. This is a safety feature to stop any
potential attacker disarming the system after a
Personal Attack alarm has started.
Using
The system is armed by pressing the Arm or
Home button for at least 1 second (this delay
feature prevents accidental operation).
The system is disarmed by pressing the Disarm
button in the same way.
The switch at the side prevents the keyfob from
transmitting accidentally.
¥ The keyfob can also be used to answer an
incoming telephone call by pressing the Disarm
button twice for 1 second with a pause between
and then to close the call by pressing the Disarm
button again for 1 second.
¥ When arming the system in home mode using the
keyfob remote, the system will arm and disarm
instantly without an exit or entry countdown.
Keypad remote control accessory
Programming
Note before learning in, ensure that J1 has a
jumper link is on the two pins.
1
Enter the D/- menu and select the Add
Device sub menu.
2
When prompted by the control unit enter 0000 on
the keypad then press TEST. The Tx LED will flash
showing that the keypad is in program mode.
3
Press TEST then 1 on the keypad. The keypad
and the control unit will beep.
4
After you have assigned a zone to the keypad,
the display will show the successfully installed
device.
5
Press OK on the control unit.
6
Press Off twice on the keypad to exit program
mode, Tx LED will stop flashing.
¥ The keypad will beep every 30 seconds if the
tamper switch is open. Please ensure tamper
switch closes when mounting.
Using
To arm the system:
Enter your PIN code and press Arm.
To disarm the system:
Enter your PIN code and press Off.
To home arm the system:
Enter your PIN code and press Home.
Adding accessories
To provide additional protection you can add extra door/window contacts, PIRs, keyfob
remote controls, keypad remote controls, help buttons and smoke detectors. These are
available separately from your local stockist.
Содержание HSA3095
Страница 27: ...27 ...