Yaesu VX-8DE страница 149 Скачать руководство пользователя

Страница: 149 / 180

VX-8DR/DE O

PERATING

ANUAL

147

ODE

TEM

32: EAI

Function

: Enables/Disables the Emergency Automatic ID (EAI) feature.

Available Values

: ON / OFF

Default

: OFF

ODE

TEM

33: EAI TIME

Function

: Sets the Emergency Automatic ID (EAI) operating mode and its transmit time.

Available Values

: INT 1min ~ INT 9min / INT10min / INT15min / INT20min /

INT30min / INT40min / INT50min / CON 1min ~ CON 9min / CON10min /
CON15min / CON20min / CON30min / CON40min / CON50min

Default

: CON 5min

INT:

Interval Mode

CON: Continuous Mode

ODE

TEM

34: EMERGENCY SELECT

Function

: Select the alarms utilized when the Emergency function is engaged.

Available Values

: BEEP / STROBE / BEEP&STROBE / BEAM / BEEP&BEAM / CW /

BEEP&CW / CW-ID TX

Default

: BEEP & STROBE

BEEP:

Loud “Alarm” sounds.

STROBE:

Flashes the white LED light.

BEEP&STROBE: Loud “Alarm” sounds along with flashing of the white LED light.
BEAM:

The white LED light glows continuously.

BEEP&BEAM:

Loud “Alarm” sounds and the white LED light glows continuously.

CW:

The white LED light flashes according to the programmed Emer-
gency message (Morse Code)

at a rate of five words per minute.

BEEP&CW:

Sounds tones via the speaker, and flashes the white LED light, ac-
cording to the programmed Emergency message (Morse Code)

at a

rate of five words per minute.

CW-ID TX:

Transmits the programmed Emergency message (Morse Code)

and

flashes the white LED light, according to the programmed Emergency
message (Morse Code)

on the air beginning one minute after activa-

tion of the Emergency function.

: The internationally-recognized Morse Code “S.O.S” message (•

•

–

•

•) is

programmed at the factory for the Emergency message.

Here’s how to program the Emergency Message:
1.

Press the

key to display any previously-stored emergency message.

Press and hold the

key for two seconds to clear any previous emergency mes-

sage, if desired.

ODE

ELECTION

ETAILS

Содержание VX-8DE





















































































































































































Результаты поиска

Содержание VX-8DE

Отзывы:

Похожие инструкции для VX-8DE

Бренды по названию

Популярные бренды

Yaesu VX-8DE, Руководство по эксплуатации

Результаты поиска

Содержание VX-8DE

Отзывы:

Похожие инструкции для VX-8DE

Бренды по названию

Популярные бренды