Page 111
FT-950 O
PERATING
M
ANUAL
032 GENE uT DIAL
Function
: Selects the
μ
-TUNE mode.
Available Values
: StP1/StP2
Default Setting
: StP1
StP1: Activates the
μ
-TUNE system using “COARSE”
steps of the [
SELECT
(
μ
-TUNE
)] knob (2 steps/
click) on the 7 MHz and lower amateur bands. On
the 10/14 MHz bands, “FINE” [
SELECT
(
μ
-
TUNE
)] knob steps will be used (1 step/click).
StP2: Activates the
μ
-TUNE system using “FINE” steps
of the [
SELECT
(
μ
-TUNE
)] knob (1 step/click) on
the 14 MHz and lower amateur bands.
A
DVICE
:
If an optional RF
μ
Tuning Kit is not connected, this ad-
justment has no effect.
033 GENE MIC SCN
Function
: Enables/disables scanning access via the
microphone’s [
UP
]/[
DWN
] keys.
Available Values
: On/OFF
Default Setting
: On
034 GENE SCN RSM
Function
: Selects the Scan Resume mode.
Available Values
: CAr/5SEc
Default Setting
: 5SEc
CAr: The scanner will hold until the signal disappears,
then will resume after one second.
5SEc: The scanner will hold for five seconds, then resume
whether or not the other station is still transmitting.
035 GENE FRQ ADJ
Function
: Adjusts the reference oscillator.
Available Values
: –25 ~ 0 ~ +25
Default Setting
: 0
Connect a 50-Ohm dummy load and frequency counter to
the antenna jack; adjust the [
CLAR/VFO-B
] knob so that
the frequency counter reading is same as the VFO fre-
quency while pressing the
PTT
switch.
A
DVICE
:
Do not perform this Menu item unless you have a high
performance frequency counter. Perform this Menu item
after aging the transceiver and frequency counter suffi-
ciently (at least 30 minutes).
MODE-AM G
ROUP
036 A3E MICGAIN
Function
: Sets the microphone gain for the AM mode.
Available Values
: Ur/0 ~ 100
Default Setting
: Ur
When this menu is set to “Ur”, you may adjust the micro-
phone gain using the front panel’s [
MIC GAIN
] knob.
MODE-CW G
ROUP
037 A1A F-TYPE
Function
: Selects the desired keyer operation mode for
the device connected to the front panel’s
KEY
jack.
Available Values
: OFF/buG/ELE/ACS
Default Setting
: ELE
OFF: Disables the front panel’s keyer (“straight key” mode
for use with external keyer or computer-driven key-
ing interface).
buG: Mechanical “bug” keyer emulation. One paddle pro-
duces “dits” automatically, while the other paddle
manually produces “dahs”.
ELE: Iambic keyer with ACS (Automatic Character Spac-
ing) disabled.
ACS: Iambic keyer with ACS (Automatic Character Spac-
ing) enabled.
038 A1A F-REV
Function
: Selects the keyer paddle’s wiring configuration
for the
KEY
jack on the front panel.
Available Values
: nor/rEV
Default Setting
: nor
nor:
Tip = Dot, Ring = Dash, Shaft = Ground
rEV: Tip = Dash, Ring = Dot, Shaft = Ground
039 A1A R-TYPE
Function
: Selects the desired keyer operation mode for
the device connected to the rear panel’s
KEY
jack.
Available Values
: OFF/buG/ELE/ACS
Default Setting
: ELE
OFF: Disables the front panel’s keyer (“straight key” mode
for use with external keyer or computer-driven key-
ing interface).
buG: Mechanical “bug” keyer emulation. One paddle pro-
duces “dits” automatically, while the other paddle
manually produces “dahs”.
ELE: Iambic keyer with ACS (Automatic Character Spac-
ing) disabled.
ACS: Iambic keyer with ACS (Automatic Character Spac-
ing) enabled.
040 A1A R-REV
Function
: Selects the keyer paddle’s wiring configuration
for the
KEY
jack on the rear panel.
Available Values
: nor/rEV
Default Setting
: nor
nor:
Tip = Dot, Ring = Dash, Shaft = Ground
rEV: Tip = Dash, Ring = Dot, Shaft = Ground
M
ENU
M
ODE
GENERAL G
ROUP
