Yaesu FT-2600M Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 62

background image

FT-2600M O

PERATING

M

ANUAL

13

B

ASE

S

TATION

I

NSTALLATION

The FT-2600M is ideal for base station use as well as in mobile installations. The FT-
2600M is specifically designed to integrate into your station easily, using the information
to follow as a reference.

AC Power Supplies

Operation of the FT-2600M from an AC line

requires

a power source capable of providing

at least 10 Amps continuously at 13.8 Volts DC. The FP-1023A, FP-1025A, and FP-1030A
AC Power Supplies are available from your Yaesu dealer to satisfy these requirements.
Other well-regulated power supplies may be used, as well, if they meet the above voltage
and current specifications.

Use the DC power cable supplied with your transceiver for making power connections to the
power supply. Connect the

RED

power cable lead to the

POSITIVE

(+) power supply termi-

nal, and connect the

BLACK

power cable lead to the

NEGATIVE

(-) power supply terminal.

Packet Radio Terminal Node Controller (TNC)

The FT-2600M provides a convenient rear-panel

DATA

jack for easy connections to your

TNC. This connector is a standard Dsub 9-pin connector, widely available from electron-
ics parts suppliers.

The FT-2600M’s

DATA

jack connections are optimized for the data transmission and recep-

tion speed in use. In accordance with industry standards, the signal levels, impedances, and
bandwidths are significantly different on 9600 bps as opposed to 1200 bps. If your TNC does
not provide multiple lines to accommodate such optimization, you may still be able to utilize
your TNC, if it is designed for multiple-radio use, by connecting the TNC “Radio 1” port to
the 1200 bps lines on the FT-2600M, and the “Radio 2” port to the 9600 bps lines.

The pin connections of the

D

ATA

connector are shown below.

Installation

Pin

Label

Notes

1

Squelch Signal Output

Carrier In: Closed (Open Collector)
Maximum voltage 16 V, Max. sink current 10 mA

2

Packet Rx Data Output (9600 bps) Typ. output level 600 mV/10 k

W

3

Packet Tx Data Input (9600 bps)

Typ. input level 800 mV/600

W

, Max. input 1.2 V

4

Packet Rx Data Output (1200 bps) Typ. output level 200 mV/600

W

5

Gr ound

-

6

Not Used

-

7

External PTT Signal Input

GND: TX, Open: RX

8

DC Output

Switched and regulated DC 5.0 V output for supplying power to
an accessory. Maximum output current is 50 mA

9

Packet Tx Data Input (1200 bps)

Typ. input level 40 mV/600

W

«
...
13
14
15
16
17
...
»

Содержание FT-2600M































































Отзывы:

Нет отзывов

Похожие инструкции для FT-2600M

Бренд: Icom Страницы: 5

Бренд: Varec Страницы: 38

Бренд: Daikin Страницы: 4

Бренд: M-system Страницы: 4

Бренд: M-system Страницы: 4

Бренд: M-system Страницы: 4

Бренд: M-system Страницы: 2

Бренд: M-system Страницы: 2

Бренд: M-system Страницы: 2

Бренд: RadioMaster Страницы: 10

Бренд: Xoro Страницы: 44

Бренд: Yaesu Страницы: 15

Бренд: Yaesu Страницы: 99

Бренд: Yaesu Страницы: 20

Бренд: Yaesu Страницы: 176

Бренд: Zenith Страницы: 8

Бренд: Fly Sky Страницы: 2

Бренд: Lectrosonics Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды