Yaesu FT-2600M Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 62

background image

FT-2600M O

PERATING

M

ANUAL

8

This chapter describes the installation procedure for integrating the FT-2600M into a typi-
cal amateur radio station. It is presumed that you possess technical knowledge and concep-
tual understanding consistent with your status as a licensed radio amateur. Please take
some extra time to make certain that the important safety and technical requirements de-
tailed in this chapter are followed closely.

P

RELIMINARY

I

NSPECTION

Inspect the transceiver visually immediately upon opening the packing carton. Confirm
that all controls and switches work freely, and inspect the cabinet for any damage. Gently
shake the transceiver to verify that no internal components have been shaken loose due to
rough handling during shipping.

If any evidence of damage is discovered, document it thoroughly and contact the shipping
company (or your local dealer, if the unit was purchased over-the-counter) so as to get
instructions regarding the prompt resolution of the damage situation. Be certain to save the
shipping carton, especially if there are any punctures or other evidence of damage incurred
during shipping; if it is necessary to return the unit for service or replacement, use the
original packing materials but put the entire package inside another packing carton, so as
to preserve the evidence of shipping damage for insurance purposes.

I

NSTALLATION

T

IPS

To ensure long life of the components, be certain to provide adequate ventilation around
the cabinet of the FT-2600M.

Do not install the transceiver on top of another heat-generating device (such as a power
supply or amplifier), and do not place equipment, books, or papers on top of the FT-2600M.
Avoid heating vents and window locations that could expose the transceiver to excessive
direct sunlight, especially in hot climates. The FT-2600M should not be used in an envi-
ronment where the ambient temperature e60º C (140º F).

S

AFETY

I

NFORMATION

The FT-2600M is an electrical apparatus, as well as a generator of RF (Radio Frequency)
energy, and you should exercise all safety precautions as are appropriate for this type of
device. These safety tips apply to

any

device installed in a well-designed amateur radio

station.

r

Do not allow unsupervised children to play in the vicinity of your transceiver or an-
tenna installation.

r

Be certain to wrap any wire or cable splices thoroughly with insulating electrical tape,
to prevent short circuits.

Installation

«
...
8
9
10
11
12
...
»

Содержание FT-2600M































































Отзывы:

Нет отзывов

Похожие инструкции для FT-2600M

DuoPak APD 2015

Бренд: Absolute Process Instruments Страницы: 2

Бренд: B&G Страницы: 4

Бренд: Cambridge Audio Страницы: 30

Бренд: Cambridge Audio Страницы: 9

Бренд: Cambridge Audio Страницы: 51

Бренд: Cambridge Audio Страницы: 55

Бренд: Zaxcom Страницы: 22

Бренд: Hammarlund Страницы: 38

Бренд: Hammarlund Страницы: 22

Бренд: Hammarlund Страницы: 87

Sat-Light 7410F

Бренд: Foxcom Страницы: 74

BTL6-A 5 00-M0500-PF-S115

Бренд: Balluff Страницы: 22

Бренд: Icom Страницы: 16

Бренд: Denon Страницы: 2

Бренд: Harmonic Страницы: 50

Бренд: Fisher Страницы: 12

Бренд: Sennheiser Страницы: 2

Бренд: Yaesu Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды