Yacht Devices NMEA 2000 YDBM-01 Скачать руководство пользователя

Страница: 36 / 66

— 36 —

Syntax

Examples

Description

YD:SHUNT_CUR [1..2500]

YD:SHUNT_CUR 10

Set external shunt rated current

in amperes (1..2500 A, integer value).

Specify this value according to your

actual shunt's nominal settings.
Factory setting: 50

YD:SHUNT_VOL [50..100]

SHUNT_VOL 75

External shunt voltage drop

in millivolts (50..100 mV, integer

value). Specify this value according

to your actual shunt's nominal

settings.
Factory setting: 75

YD:TEMPERATURE

[0..252|UNKNOWN]

YD:TEMPERATURE 1

Sets NMEA 2000 temperature

instance for the battery temperature

measuring device (0..252, integer

value), don’t confuse with NMEA

2000 device instance or data type.

If no such device is present, use

UNKNOWN.
Factory setting: UNKNOWN

YD:BATTERY [0..252]

YD:BATTERY 2

Sets NMEA 2000 battery instance

of the Device (0..252, integer value),

0 for the first or single battery.

Factory setting: 0

Table 1 continued

Содержание NMEA 2000 YDBM-01



































































Результаты поиска

Содержание NMEA 2000 YDBM-01

Отзывы:

Похожие инструкции для NMEA 2000 YDBM-01

Бренды по названию

Популярные бренды

Yacht Devices NMEA 2000 YDBM-01, Руководство пользователя

Результаты поиска

Содержание NMEA 2000 YDBM-01

Отзывы:

Похожие инструкции для NMEA 2000 YDBM-01

Бренды по названию

Популярные бренды