Xylem GOULDS e-AB Series Скачать руководство пользователя страница 28

Страница: 28 / 56

Push button

Function

• Main view (see parameter 6.4.1): decreases the

required value for the selected control mode

• Parameter menu (see parameter 6.4.2):

decreases the displayed parameter index

• Parameter view / editing (see parameter 6.4.2):

decreases the value of the displayed parameter

• Zero pressure auto-calibration (see parameter

6.5, P44): automatic calibration of the pressure

sensor.

• Main view (see parameter 6.4.1): increases the

required value for the selected control mode

• Parameter menu (see parameter 6.4.2):

increases the displayed parameter index

• Parameter view / editing (see parameter 6.4.2):

increases the value of the displayed parameter

• Zero pressure auto-calibration (see parameter

6.5, P44): automatic calibration of the pressure

sensor.

• Main view (see parameter 6.4.1): START/STOP

the pump

• Parameter menu (see parameter 6.4.2): switches

to parameter view / editing

• Parameter view / editing (see parameter 6.4.2):

saves the value of the parameter.

long press

• Main view (see parameter 6.4.2): switches to

parameter selection

• Parameters Menu: switches to Main Visualization

and

Main view: alternates between Speed and Head

units of measure (see parameter 6.4.1).

and

Main view: alternates between Speed and Head

units of measure (see parameter 6.4.1).

6.4 LED description

6.4.1 POWER (power supply)

When ON (POWER) the pump is powered and the electronic devices are operational.

6.4.2 STATUS

LED

Status

Off

Pump unit stopped

Green steady

Pump unit in operation

Flashing green and orange

Non-locking alarm with the pump unit in operation

Orange steady

Non-locking alarm with the pump unit stopped

Red steady

Locking error, the pump unit cannot be started

6.4.3 SPEED (speed bar)

The speed bar consists of 10 LEDs, each representing the speed range between parameter

P27 (minimum speed) and parameter P26 (maximum speed) from 0-100% in intervals of

10%.

6 System Setup and Operation

Smart Pump Range INSTRUCTION MANUAL

Содержание GOULDS e-AB Series

























































Результаты поиска

Содержание GOULDS e-AB Series

Отзывы:

Бренды по названию

Популярные бренды

Xylem GOULDS e-AB Series, Инструкция по эксплуатации

Результаты поиска

Содержание GOULDS e-AB Series

Отзывы:

Бренды по названию

Популярные бренды