manualshive.com logo in svg

Xylem Flygt 3060, Инструкция по установке, эксплуатации и обслуживанию

Поделиться
Скачать
Xylem Flygt 3060 Скачать руководство пользователя страница 4

View of terminal board and sensor connections........................................................................21
Motor cable, stator leads and thermal contacts connection to terminal board.....................22

Check the impeller rotation.............................................................................................................23

Operation..............................................................................................................................................24

Precautions.........................................................................................................................................24
Distance to wet areas........................................................................................................................24
Noise level..........................................................................................................................................24
Start the pump...................................................................................................................................24
Clean the pump.................................................................................................................................25

Maintenance.........................................................................................................................................26

Precautions.........................................................................................................................................26
Maintenance guidelines...................................................................................................................26
Torque values....................................................................................................................................26
Service................................................................................................................................................27

Inspection........................................................................................................................................27
Major overhaul................................................................................................................................29

Change the oil...................................................................................................................................29

Empty the oil...................................................................................................................................29
Fill with oil........................................................................................................................................29

Replace the impeller.........................................................................................................................30

Remove the impeller......................................................................................................................30
Install the impeller..........................................................................................................................30
Adjust the impeller.........................................................................................................................30

Troubleshooting...................................................................................................................................31

Introduction.......................................................................................................................................31
The pump does not start..................................................................................................................31
The pump does not stop when a level sensor is used.................................................................32
The pump starts-stops-starts in rapid sequence...........................................................................32
The pump runs but the motor protection trips.............................................................................33
The pump delivers too little or no water........................................................................................34

Technical Reference............................................................................................................................35

Application limits...............................................................................................................................35
Motor data..........................................................................................................................................35
Specific motor data...........................................................................................................................35
Dimensions and weights..................................................................................................................38
Performance curves..........................................................................................................................42

Table of Contents

2

Flygt 3060 Installation, Operation, and Maintenance Manual

Содержание Flygt 3060



















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды