Xylem Flygt 3060 Скачать руководство пользователя страница 37

Страница: 37 / 50

Technical Reference

Application limits

Data

Description

Media (liquid)

temperature

Standard temperature version: Maximum temperature 40°C (104°F)
Warm media (liquid) version: Maximum temperature 70°C (158°F)
Warm media (liquid) version with external cooling: Maximum temperature 90°C

(195°F)
Warm liquid has certain operational limitations, which are stated on a plate on the

pump.

pH of the pumped media

(liquid)

0–14

Media (liquid) density

Maximum density: 1100 kg/m

(9.2 lb. per US gal.)

Depth of immersion

20 m (65 ft.)

Other

For specific weight, current, voltage, power rating, and speed of the pump, see the data

plate on the pump. For starting current, see

Motor data

(page 35).

For other applications, contact the local sales and service representative for

information.

Motor data

Feature

Description

Motor type

Squirrel-cage induction motor

Frequency

Standard version: 50 or 60 Hz

Supply

1-phase or 3-phase

Starting method

Direct on-line

Maximum starts per

hour

30 evenly spaced starts per hour

Code compliance

IEC 60034-1

Rated output variation

±10%

Voltage variation without

overheating

±10%, provided that it does not run continuously at full load

Voltage imbalance

tolerance

Stator insulation class

H (180°C [360°F])

Specific motor data

Technical Reference

Flygt 3060 Installation, Operation, and Maintenance Manual

Содержание Flygt 3060



















































Результаты поиска

Содержание Flygt 3060

Отзывы:

Бренды по названию

Популярные бренды

Xylem Flygt 3060, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Flygt 3060

Отзывы:

Бренды по названию

Популярные бренды