manualshive.com logo in svg

Xylem Flygt 3060, Инструкция по установке, эксплуатации и обслуживанию

Поделиться
Скачать
Xylem Flygt 3060 Скачать руководство пользователя страница 31

Major overhaul

For a major overhaul, take this action in addition to the tasks listed under Inspection.

Service item

Action

Support and main bearing

Replace the bearings with new bearings.

Mechanical seal

Replace with new seal units.

Change the oil

A paraffin oil with viscosity close to ISO VG32 is recommended. The pump is delivered
from the factory with this type of oil. In applications where poisonous properties are of less
concern, a mineral oil with viscosity up to ISO VG32 can be used.

Empty the oil

1. Lay the pump on its side.

Lock the pump with supports to prevent it from rolling over.

2. Remove the oil screw.

WARNING:

The oil housing may be pressurized. Hold a rag over the oil plug to
prevent oil from spraying out.

3. Turn the pump so that the oil hole faces downwards and let the oil run out.

In order to get all the oil out, the pump must be raised upright for a short while during
drainage.

WS001765A

Fill with oil

1. Replace the oil screw O-ring.
2. Turn the pump so that the oil hole faces upwards and fill with new oil.

Quantity: 0.5 L (0.52 qt.)

3. Put the oil screw back and tighten it.

Maintenance

Flygt 3060 Installation, Operation, and Maintenance Manual

29

Содержание Flygt 3060



















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды