manualshive.com logo in svg

Xylem Flygt 2008 Ready 8, Инструкция по установке, эксплуатации и обслуживанию

Поделиться
Скачать
Xylem Flygt 2008 Ready 8 Скачать руководство пользователя страница 4

6.5.2  Install the motor cable................................................................................................29

7  Troubleshooting....................................................................................................................... 31

7.1  The pump does not start...................................................................................................31
7.2  The pump does not stop when a level sensor is used.................................................. 32
7.3  The pump starts-stops-starts in rapid sequence............................................................33
7.4  The pump runs but the motor protection trips..............................................................33
7.5  The pump delivers too little or no water.........................................................................34

8  Technical Reference.................................................................................................................36

8.1  Application limits............................................................................................................... 36
8.2  Motor data.......................................................................................................................... 36
8.3  Specific motor data: Ready 8........................................................................................... 36
8.4  Specific motor data: Ready 8S......................................................................................... 37
8.5  Dimensions and weights...................................................................................................38
8.6  Performance curves...........................................................................................................39

Table of Contents

2

2008 Ready 8, 8S Installation, Operation, and Maintenance

Содержание Flygt 2008 Ready 8













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды