manualshive.com logo in svg

Xylem Flygt 2008 Ready 8, Инструкция по установке, эксплуатации и обслуживанию

Поделиться
Скачать
Xylem Flygt 2008 Ready 8 Скачать руководство пользователя страница 17

WS001396B

4.2.1  Connect the motor cable to the pump

NOTICE:

Leakage into the electrical parts can cause damaged equipment or a blown fuse. Keep
the end of the motor cable dry at all times.

1. Check the data plate to see which connections are required for the power supply.
2. Connect the motor cable conductors, including ground (earth) , to the terminal or

starter unit.

3. Make sure that the pump is correctly connected to ground (earth) .
4. Firmly tighten the cable entry into its bottom-most position.

The seal sleeve and the washers must conform to the outside diameter of the cables.

DANGER: Explosion/Fire Hazard

Special rules apply to installations in explosive or flammable atmospheres. Do not install
the product or any auxiliary equipment in an explosive zone unless it is rated explosion-
proof or intrinsically-safe. If the product is EN/ATEX-, MSHA- or FM-approved, then see
the specific EX information in the Safety chapter before taking any further actions.

4  Installation

2008 Ready 8, 8S Installation, Operation, and Maintenance

15

Содержание Flygt 2008 Ready 8













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды