Xtreme XR1270 Скачать руководство пользователя страница 49

Страница: 49 / 80

For information call (800) 497-1704

Page 47

XR1270

Operation

Pre-Operation Inspection

To perform the pre-operation inspection make sure the

forklift is NOT running, the engine is cool, the forklift is

parked on level ground, the boom is completely retracted,

and the frame is level

NOTE:

Copy and use the Pre-Operation Inspection

Checklist in this section



Warning

Wear appropriate protective clothing. Personal

protective equipment can include, but is not limited to

hardhat, gloves, footwear, safety glasses or goggles,

and hearing protection. Make sure clothing is snug

and properly belted. DO NOT wear loose clothing,

jewelry, watches, or anything that can catch on the

forklift, such as controls and moving parts. Wearing

loose clothing while operating the forklift could result

in death or serious injury.

Perform a pre-operation inspection and

functional tests at the beginning of each

work shift. Perform the pre-operation

inspection first. DO NOT perform the

pre-operation inspection with the engine running or

hot. Contact with moving or heated parts could cause

death or serious injury.

Perform the pre-operation inspection and

functional tests in an open area.

Become familiar with all safety and hazard

labels, regulations, and procedures. Make

sure all proper labels are attached to the

forklift and remain legible.

Remove forklift from service and place “Do

Not Operate” tags on the Starter switch

and steering wheel if anything is found

to be in need of repair or maintenance,

defective, or unsafe in any way.



Caution

Contact with hot surfaces or the exhaust

pipe after the forklift has been operated

could result in minor or moderate personal

injury.



Warning

Always check the condition of the seat belt

and mounting hardware before operating

the forklift. If the seat belt or mounting

hardware is defective, it may not properly

restrain the operator, which could result in death or

serious injury.
• DO NOT operate the forklift until the seat belt or

mounting hardware is replaced, if worn or damaged.

• The seat belt MUST be worn while operating the

forklift. Failure to wear the seat belt could result in

death or serious injury.

Check hydraulic oil lines, tubes,

and hoses carefully. DO NOT

use your bare hand to check

for potential leaks. Always use

a board or cardboard when checking for a hydraulic

leak. Escaping hydraulic fluid under pressure, even

a pinhole size leak, can penetrate body tissue, which

could cause death or serious injury. If hydraulic fluid is

injected into your skin, a doctor familiar with this type

of injury must treat it immediately.

Personal injury could result

from hydraulic oil pressure

or hot oil. DO NOT remove a

hydraulic tank filler cap unless

it is cool enough to touch with bare hands. Remove

the hydraulic tank filler cap slowly to relieve pressure.

Relieve all pressure in a hydraulic system before any

caps, lines, fittings, or related items are disconnected

or removed.
Never remove the radiator cap while the engine

is hot. The cooling system is under pressure. Hot

coolant could cause severe burns or eye injury. Wear

protective clothing and safety glasses.

Содержание XR1270

















































































Результаты поиска

Содержание XR1270

Отзывы:

Похожие инструкции для XR1270

Бренды по названию

Популярные бренды

Xtreme XR1270, Инструкция по эксплуатации и безопасности

Результаты поиска

Содержание XR1270

Отзывы:

Похожие инструкции для XR1270

Бренды по названию

Популярные бренды